Drawing
Selection table
One row per thread size, with its own link (/parts/nutplates/ms21047/#MS21047-04). The part number shown is the dry film lubricated, plain-hole form; the letters below change finish and holes, not size.
| Part no. | Thread | A max | B max | C | J | H max | Ø K | Ø P max | V max | Axial, lbf min | lb / 100 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MS21047L04 | 4-40 | .948 | .260 | .344 | .688 | .143 | .098 | .168 | .047 | 750 | .14 |
| MS21047L06 | 6-32 | .948 | .265 | .344 | .688 | .171 | .098 | .208 | .047 | 1,130 | .18 |
| MS21047L08 | 8-32 | .948 | .297 | .344 | .688 | .250 | .098 | .248 | .047 | 1,720 | .28 |
| MS21047L3 | 10-32 | .948 | .328 | .344 | .688 | .250 | .098 | .274 | .047 | 2,460 | .29 |
| MS21047L4 | 1/4-28 | 1.260 | .414 | .500 | 1.000 | .281 | .098 | .344 | .055 | 4,580 | .53 |
| MS21047L5 | 5/16-24 | 1.292 | .505 | .500 | 1.000 | .328 | .130 | .417 | .065 | 7,390 | .80 |
Inches. From Table I of MS21047 Rev. F (1 Feb 1994). C ±.005, J ±.002, K +.005 −.000 as toleranced on the sheet. Ø P is the maximum barrel diameter. Weight is the standard's figure per 100 pieces. Rows shown are the sizes this sheet covers; the standard may list more.
How to read the part number
| Part no. | Meaning |
|---|---|
| MS21047-08 | Plain rivet holes, no dry film lubricant |
| MS21047L08 | Dry film lubricant (L) |
| MS21047-08K | Countersunk or dimpled rivet holes (K) |
| MS21047L08K | Both |
K (countersunk or dimpled rivet holes) is listed for dash 04, 06, 08, 3, 4, 5. Without lubricant the L becomes a dash.
What it is for
All-metal fixed self-locking nutplate, steel, 125 ksi, 450 °F. Rated to 450 °F.
Rivet hole spacing J differs between nutplate types and sizes: check J before installing on an existing hole pattern.
Choose the size from the screw thread, then confirm J and C against the hole pattern and the edge distance of the flange it rivets to.
Limits — when NOT to use this
- Approved data governs. Use the nutplate and rivets the maintenance manual or IPC specifies.
- The MS sheet is a public-domain revision. These MS standards were later replaced by NASM equivalents. Check the current revision before buying to a drawing.
- Grip with nutplates. Where the proper bolt grip is not available, AC 43.13-1B par. 7-37 says to add shims under the plate, not washers.
- Rivets for the lugs, and their edge distance, come from the repair data, not from this sheet.
Sources
- MS21047 Rev. F, 1 Feb 1994 — Nutplate, Self-Locking, Two Lug, Low Height — Table I, dash numbers and dimensions; notes and requirements. Public domain, distribution unlimited.
- FAA AC 43.13-1B, par. 7-37 — shims, not washers, under plate nuts.