What it is
Where to buyA rivet set is a hardened steel bar with three parts: the shank goes into the gun barrel, the collar is held by the retainer spring, and the body carries the face to the rivet head. The gun's piston hits the shank end and the set passes each blow to the head while a bucking bar forms the shop head on the other side.
The face to the head decides the set. A universal (MS20470) head takes a cupped set, by size; a flush 100° head takes a flat set; tight access takes an offset or long-reach set. The shank to suit the gun barrel is 0.401 in (10.2 mm) on most guns and 0.498 in (12.6 mm) on larger guns. Keep the face polished, the retainer spring always fitted, and never fire the gun without the set on the work. Store sets in a rack.
Drawing
Types and sizes
| Set | Face | Use |
|---|---|---|
| Universal | Cupped, by size | Universal (MS20470) heads; one set per rivet diameter. |
| Flush | Flat, polished | Flush 100° heads; the flat face covers the head and does not mark the skin. |
| Flush with guard | Flat, inside a rubber or plastic guard | Flush heads on painted or clad skin. |
| Offset | Cupped or flat, body bent to one side | Rivets next to a flange, a frame or a stiffener. |
| Long reach | Cupped or flat, long straight body | Rivets deep in a channel or behind a lip. |
| Shank 0.401 in (10.2 mm) | Any | Most rivet guns. |
| Shank 0.498 in (12.6 mm) | Any | Larger guns for larger rivets. |
What to check when buying
| Check | What to look for |
|---|---|
| Shank | 0.401 in (10.2 mm) or 0.498 in (12.6 mm), the size of your gun barrel. |
| Face | Cup size marked for the rivet diameter and head style; flush faces flat and polished. |
| Collar | Fits the retainer spring of your gun. |
| Hardness | Hardened face and shank end, a tough body; no burrs or tool marks. |
| Length | Short sets for open work, offset and long-reach sets for the places your aircraft needs. |
| Storage | Sets sold with a rack or a case, so faces do not knock together. |
Accessories
| Item | What it is for |
|---|---|
| Retainer spring | One per set length and shank size; keep spares. |
| Set rack | Keeps faces apart and sets sorted by size. |
| Guard for flush sets | Protects painted and clad skin. |
| Polishing cloth and fine abrasive | Keeps the face polished. |
| Wood block | To set and test the hit of the gun, never against metal. |
Care
Face. Keep the face polished and free of nicks: a scratch on the face prints on every rivet head and on the skin.
Storage. Store sets in a rack, never loose in a drawer.
Retainer spring. Replace a stretched or cracked spring at once.
Safety
Retainer. Always fit the retainer spring on the set and check it before every job.
Never fire the gun without the set on the work. A gun fired in the air can throw the set out of the barrel.
Air off. Disconnect the hose before you change a set or a retainer spring.
Questions people actually ask
Which shank size do I need?
The size of your gun barrel: 0.401 in (10.2 mm) on most guns, 0.498 in (12.6 mm) on larger guns. See rivet guns.
Why does the set mark the skin?
A worn or wrong-size cup, a set held off square or a scratched flush face. Check the face on a rivet of the size and hold the set square to the head.
Can one set drive several rivet sizes?
A flush set can, if its face is wider than the head. A universal set is cupped for one rivet diameter.
Where to buy
Are you a distributor? Get listed →
Distributors coming soon.
