Slip Rolls

A slip roll curves flat sheet into cylinders, tubes and gentle skin contours. Buy it by width, mild steel capacity and roll diameter, and check the rolls are clean and smooth: every mark on a roll prints on aluminum.

View PDF

What it does

Where to buy

A slip roll has three rolls between two end frames. The two front rolls are geared together and turned by the handle; they grip the sheet and feed it. The lower front roll is set to the sheet thickness with its adjusting screws.

The rear roll sits behind the front pair and bends the sheet up as it comes through. Raising it makes a tighter curve. There is no scale for the radius: it is set by trial, in several passes, and checked with a radius gauge or a template.

The upper roll release frees one end of the upper roll so a closed cylinder slides off. Wire grooves at one end of the rolls form a curve over a wired edge without flattening it; on 24 in machines they are commonly 3/16, 1/4 and 5/16 in (4.8, 6.4 and 7.9 mm).

A cone or tapered part is rolled with the rear roll set closer at one end than at the other; the amount is found by trial.

Drawing

ITEMDESCRIPTION1END FRAME2UPPER FRONT ROLL3LOWER FRONT ROLL4REAR ROLL5HANDLE6DRIVE GEARS7ADJUSTING SCREW, LOWER8ADJUSTING SCREW, REAR9UPPER ROLL RELEASE10WIRE GROOVE11SHEETSLIP ROLL, HANDSHEET 1 OF 1DWG TAP-TG-098REV ASCALE 1:2CAPACITY, MILD STEELWIDTH INGAUGE (IN)2420 GA (0.036)3622 GA (0.030)5016 GA (0.060)ROLL DIAMETERWIDTH INROLLS IN24-362 (50.8)503 (76.2)NOTES1.DIMENSIONS IN INCHES(MM).2.FRONT ROLLS FEED THESHEET, REAR ROLL SETSTHE CURVE.3.SET THE LOWER FRONT ROLLTO THE SHEET THICKNESS.4.RATED CAPACITY IS FORMILD STEEL.5.WIRE GROOVES 3/16, 1/4,5/16 ON 24 IN ROLLS.6.KEEP THE ROLLS CLEAN FORALUMINUM.24 (610)AACFRONT VIEW, ROLLS BROKENSCALE 1:43/16 (4.8)1/4 (6.4)5/16 (7.9)DETAIL C, WIRE GROOVESSCALE 2:12 (50.8)SECTION A-ASCALE 1:21234567891011
Hand slip roll, 24 in (610 mm) forming length: front view with the handle, drive gears and upper roll release; section A-A through the three 2 in (50.8 mm) rolls with the sheet being curved; detail C of the wire grooves.

Types and sizes

TypeWidth, capacity, rollsUse
Hand slip roll, 24 in24 in (610 mm); 20 gauge, 0.036 in (0.91 mm) mild steel; ⌀2 in (50.8 mm) rollsTubes, ducts, fairings and patches in thin sheet
Hand slip roll, 36 in36 in (914 mm); 22 gauge, 0.030 in (0.76 mm) mild steel; ⌀2 in (50.8 mm) rollsLonger skins and wraps in thin sheet
Hand slip roll, 50 in50 in (1270 mm); 16 gauge, 0.060 in (1.52 mm) mild steel; ⌀3 in (76.2 mm) rollsLong panels and heavier sheet
Power slip rollSame three-roll layout with a motor driveRepeated parts and long runs
Shear, brake and roll combinationThree machines on one bench frameShops that need all three in one place

What to check when buying

CheckWhat to look for
Width and capacityForming width and gauge for mild steel on the plate; with the same rolls, a wider machine is rated for thinner sheet
Roll diameterThe sheet wraps around the upper roll, so that roll sets the tightest curve; larger rolls bend less across the width
Roll finishGround, smooth and free of nicks or rust; any mark on a roll prints on the sheet
Wire groovesSizes that match the wire you use, commonly 3/16, 1/4 and 5/16 in on 24 in machines
AdjustmentScrews at both ends of the lower and rear rolls, so the rolls set parallel for a cylinder or angled for a cone
Upper roll releaseOpens without tools and closes square, so a closed cylinder slides off
MountingHoles to bolt the frames to a bench or stand that does not move when you crank

Accessories

ItemWhat it is for
Radius gauges or a templateChecking the curve between passes
StandHolds the machine at working height and leaves room for the sheet to come round
Clean lint-free cloth and solventWiping the rolls before aluminum
Light machine oilGears, journals and adjusting screws
Protective filmCovers clad sheet where the rolls would mark it

Care

Wipe the rolls clean before rolling aluminum: steel particles pressed into the sheet start corrosion. Keep the rolls free of rust and nicks, and cover them when the machine is not in use.

Oil the gears, journals and adjusting screws. Never roll sheet thicker or harder than the rating: it bends the rolls, and a bent roll gives an uneven curve on every part after.

Safety

Keep fingers, gloves, sleeves and loose clothing clear of the rolls: the front rolls pull in whatever they grip. Bolt the machine down before use.

Sheet edges are sharp; deburr them before rolling and handle the rolled part by its edges with care.

Questions people actually ask

How do I set the radius on a slip roll?

There is no scale. Set the rear roll by trial, roll, check the curve with a radius gauge or template, and raise the rear roll a little for the next pass until the curve matches.

Why does the start of the sheet stay flat?

The leading edge has not passed over the rear roll yet. Lift the sheet against the upper roll as it starts, or roll it in from both ends.

Can a slip roll make a cone?

Yes. Set the rear roll closer to the front rolls at one end than at the other; the amount is found by trial.

Can I roll a sheet with a wired edge?

Yes. Run the wired edge in the groove that fits the wire, with the rolls set a little wider at that end so the wire is not flattened.

What capacity do I need?

Ratings are for mild steel: 20 gauge on a common 24 in machine, 22 gauge on a 36 in and 16 gauge on a 50 in. Buy above the thickest sheet you roll and check the maker's data for aluminum.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close