Drill Motors: Pistol-Grip and Angle Drills

The drill motor that does most aircraft sheet metal work is the pneumatic pistol grip: light, with good speed control and no sparks near fuel. Angle drills reach where it does not fit, and a spring drill stop keeps the bit from going too deep.

View PDF

What it does

Where to buy

A drill motor turns the bit; the hole quality comes from the hand that holds it. It has to stay square to the work at 90 degrees, run at the right speed and cut without being pushed.

Air motors are the shop standard. They are light, the throttle lever gives fine speed control, and with no brushes they make no sparks around fuel and other flammables, where an electric drill is a fire hazard.

Speed comes from the metal: 200 to 300 sfm for aluminum alloy, 30 to 50 sfm for mild steel, and rpm = CS x 4 / D with D the drill diameter in inches.

Drawing

ITEMDESCRIPTION1CHUCK2DRILL BIT3NOSE4MOTOR HOUSING5THROTTLE LEVER6HANDLE7AIR INLET8STOP COLLAR9STOP CAGE10SPRING11SHEETMOTOR, DRILL, PNEUMATICSHEET 1 OF 1DWG TAP-TG-058REV ASCALE 1:1.82CUTTING SPEEDMETALSFMALUMINUM200-300MILD STEEL30-50NOTES1.INCHES (MM).2.RPM = CS X 4 / D.3.HOLD AT 90 DEG TOTHE WORK.4.DISCONNECT AIR WHENNOT IN USE.5.REPAIR DATA GOVERNS.SIDE VIEWSCALE 0.55:1FRONT VIEWSCALE 0.55:1TRAVELSPRING DRILL STOP, IN SECTIONSCALE 1:11234567891011
Pneumatic pistol-grip drill motor in side and front view, and a spring drill stop on the bit in section: the travel left between collar and cage sets the depth.

Types

TypeWhere it fitsNotes
Pneumatic pistol gripMost sheet metal and repair drillingLight, good speed control, no sparks
Right-angle drillInside structure where a pistol grip does not fitTakes threaded drill bits in several lengths
45 degree drillBetween frames and stringers, close to a flangeNever start it without a firm hold on the angle head
Lower speed, higher torque motorDeep holes, corrosion-resistant steel, titaniumSlower spindle for hard metals
Electric drillBench work away from the aircraftSpark hazard near fuel and flammables
Drill pressAccurate holes in loose partsClamp the part: an unclamped part can bind and spin

What to check when buying

CheckWhat to look for
SpeedFree speed that suits the metal and bit sizes you drill; a lower speed motor for steel and titanium
ThrottleA lever that feathers the speed smoothly from a crawl to full
ChuckKeyed or keyless, runs true, holds the bit sizes you use; threaded heads on angle drills
Weight and balanceLight enough to hold square with both hands for a full rivet row
ExhaustAir blown away from the hand and the work
Air inletA thread that matches the shop couplers
NoiseThe rated sound level, for hearing protection

Accessories

ItemWhat it is for
Spring drill stopStops the bit at a set depth and keeps the chuck off the skin
Drill bitsNumber and fraction sizes, 135 degree split point for aluminum
Angle headsRight-angle and 45 degree heads with threaded bits
Air coupler and filterClean, dry air at the motor
Tool oilDrops of oil in the inlet, as the maker says
Bit guardSupports a long extension bit

Care

Oil the motor through the air inlet as the maker says, and drain water from the air line.

Keep the chuck clean and true. A chuck that wobbles drills oversize holes.

Hang the motor up after use; a dropped motor bends the spindle.

Safety

Wear eye protection. Chips and broken bits fly.

Disconnect the air when the motor is not in use and before changing a bit.

Keep sleeves, hair and gloves away from the turning chuck, and clamp parts on a drill press.

Questions people actually ask

What rpm for drilling aluminum?

Work it out from the cutting speed: rpm = CS x 4 / D. At 300 sfm a 1/8 in bit runs at 9,600 rpm, more than most hand motors give, so run the motor at full speed with light feed.

Why air and not electric?

An air motor is light, controls speed well and makes no sparks near fuel or other flammables. Electric brush motors can arc.

What does a drill stop do?

It limits how far the bit goes through the stack. When the collar reaches the cage the bit stops, so it cannot plunge through and damage what is behind the skin.

When do I need an angle drill?

When a pistol grip cannot sit square to the hole: inside structure, next to a flange or between frames.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close