Threaded Fastener Tools: Pin and Collar, Swaged Collar and Nutplate

A threaded pin with a collar goes in with two tools at once: a hex key holds the pin while a socket turns the collar until its drive nut shears off. Buy the key for the pin and the socket for the collar hex, then the head that reaches the place: straight, offset or power.

View PDF

What it is

Where to buy

A threaded pin with a frangible collar is installed from both ends: the pin goes into the hole from one side and the collar is threaded onto it from the other. A hex key sits in the recess in the end of the pin and holds it still, while a socket on the drive nut of the collar turns the collar down. At the preset torque the drive nut shears off at the break groove, so what stays is correctly torqued and needs no torque check afterwards.

The same key and socket work by hand, in a ratchet head or in a power driver; offset and flush heads reach a collar next to a flange or a frame. A lockbolt has a collar swaged into the grooves of the pin instead of a thread: the pull type is installed with a pneumatic pull gun and the pintail breaks off, the stump type with a riveting hammer, a swaging set and a bucking bar. A nutplate is riveted behind the sheet so a screw can go in from the front: a drill jig with a pilot pin in the screw hole places its #40 rivet holes.

Drawing

ITEMDESCRIPTION1PIN, THREADED2COLLAR, FRANGIBLE3NUT, DRIVE4GROOVE, BREAK5KEY, HEX6SOCKET, COLLAR7SHEET (REF)8JIG, NUTPLATE DRILL9PIN, PILOT10NUTPLATE, TWO-LUG11HOLE, RIVET #40TOOLS, THREADED PIN, COLLAR, NUTPLATESHEET 1 OF 1DWG TAP-TG-095REV ASCALE 1:1TOOL FOR THE JOBJOBTOOLPIN AND COLLARHEX KEY, SOCKETTIGHT ACCESSOFFSET HEADPRODUCTIONPOWER DRIVERSWAGED COLLARSWAGE TOOLNUTPLATE HOLESDRILL JIG, #40PIN SIZEDASHSHANK, IN (MM)-55/32 (4.0)-63/16 (4.8)-81/4 (6.4)-105/16 (7.9)-123/8 (9.5)NOTES1.HOLD THE PIN WITH THE HEX KEY;TURN THE COLLAR ONLY.2.THE DRIVE NUT SHEARS OFF AT THEBREAK GROOVE.3.SOCKET TO FIT THE COLLAR DRIVEHEX.4.NUTPLATE: SCREW HOLE, PILOT PIN,DRILL #40.GRIPBPIN AND COLLAR, SECTIONSCALE 3:1DETAIL B, AFTER BREAKSCALE 3:1NUTPLATE DRILL JIG, SECTIONSCALE 2:1NUTPLATE, TWO-LUG, PLANSCALE 2:11234567891011
Threaded pin and frangible collar in section at 3:1 with the hex key in the pin and the socket on the drive nut; detail at 3:1 of the collar after the drive nut has sheared off at the break groove; nutplate drill jig in section at 2:1 with its pilot pin; two-lug nutplate in plan at 2:1 with its #40 rivet holes (items 1 to 11). Tool and pin size tables.

Types and sizes

ToolSizeUse
Hex keyBy pin dash sizeSits in the recess of the pin and holds it while the collar turns.
Hand wrench with hex socketBy collar drive hexRepair work and single fasteners; the key goes through the socket.
Ratchet head, straight, offset or flushBy collar drive hexCollars next to a flange, a frame or a stringer.
Power driver, pistol gripBy collar drive hexProduction rows of pins and collars.
Pull gun and nose assemblyBy pin diameterPull-type lockbolts: swages the collar, the pintail breaks off.
Swaging set and bucking barBy pin diameterStump-type lockbolts where a pull gun does not fit.
Nutplate drill jigBy screw size and lug patternPlaces the #40 rivet holes from the screw hole.
Dimple dies, #403/32 in (2.4 mm) rivetFlush nutplate rivets in thin skin.

Pin dash number: the shank diameter in 1/32 in. -5: 5/32 in (4.0 mm); -6: 3/16 in (4.8 mm); -8: 1/4 in (6.4 mm); -10: 5/16 in (7.9 mm); -12: 3/8 in (9.5 mm). Key, socket and hole for each part number: the maker's data and the drawing govern.

What to check when buying

CheckWhat to look for
Hex keyFits the recess of each dash size you install; hard, square tip; spares in the kit.
SocketFits the collar drive hex and drives the nut only, clear of the collar base.
HeadStraight, offset or flush for the places you work; the key passes through it.
Power driverRuns on the shop air pressure; takes the same sockets and keys as the hand tools.
Swage toolNose assembly or set for the pin diameter and the pull or stump type.
Drill jigScrew size and lug pattern of your nutplates; hardened #40 guide holes; pilot pin to the screw hole.

Accessories

ItemWhat it is for
Spare hex keysOne set per dash size.
Socket set by collar hexStraight, offset and flush heads.
Grip gaugeReads the grip of the hole for the pin length.
Temporary fastenersHold the parts and the jig while drilling.
Drop cloth or trayCatches the sheared drive nuts and pintails.

Care

Keys. Replace a key with a rounded or twisted tip at once.

Sockets and heads. Keep them clean of sealant and chips; check the hex for wear.

Air tools. Oil and service them to the maker's data; keep the air dry and the hose fitting tight.

Jigs. Check the guide holes and the pilot pin for wear; a worn guide hole drills an oversize hole.

Safety

Eyes. Wear eye protection: drive nuts and pintails come off with force.

Loose parts. Collect every sheared drive nut and pintail: inside the structure they are loose objects.

Air off. Disconnect the hose before you change a key, a socket or a nose assembly.

Pinch points. Keep fingers clear of the ratchet head and the bucking bar.

Questions people actually ask

Do I need a torque wrench for a pin and collar?

No. The drive nut shears off at its torque, so the collar needs no torque check. A torque wrench is for bolts and nuts: see torque wrenches.

What does the dash number of the pin mean?

The shank diameter in 1/32 in: a dash 6 pin is 3/16 in (4.8 mm). It also tells you the key and the socket to use.

Which nutplate jig do I need?

One for the screw size and the lug pattern of your nutplates, with #40 guide holes for 3/32 in (2.4 mm) rivets and a pilot pin that fits the screw hole.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close