Rivet Cutters: Rotary and Bench Cutters

When the rivet of the right length is not on the shelf, a rivet cutter trims a longer one. The rivet goes in the hole for its diameter, shims under the head set the length, and the discs shear the shank clean.

View PDF

What it does

Where to buy

A rivet cutter shortens a solid rivet without changing anything else. It has two hardened discs on one pivot, each with a hole for every rivet diameter, commonly 3/32, 1/8, 5/32 and 3/16 in (2.4 to 4.8 mm).

The rivet drops into its hole with shims under the head. Squeezing the handles turns one disc against the other and shears the shank where the discs meet, so the length left under the head is the shim stack plus the upper disc.

The length to cut to is L = grip + 1.5D: the thickness of the stack plus one and a half shank diameters for the shop head. Rivet lengths go in steps of 1/16 in; the dash number counts the sixteenths.

Drawing

ITEMDESCRIPTION1UPPER DISC2LOWER DISC3PIVOT SCREW4UPPER HANDLE5LOWER HANDLE6GRIP7LENGTH SHIMS8RIVET9SHEAR PLANECUTTER, RIVET, ROTARYSHEET 1 OF 1DWG TAP-TG-057REV ASCALE 1.1:1RIVET LENGTHDASHIN (MM)-41/4 (6.4)-55/16 (7.9)-63/8 (9.5)-77/16 (11.1)-81/2 (12.7)DASH = 1/16 INNOTES1.INCHES (MM).2.L = GRIP + 1.5D.3.SHIMS UNDER THEHEAD SET L.4.ONE HOLE PER RIVETSIZE.3/325/323/161/8AATOP VIEWSCALE 1.1:1LSECTION A-ASCALE 3:1123456789
Rotary rivet cutter: top view with a hole for each rivet size and the two handles, section A-A through the discs with a 1/8 in rivet on its shims above the shear plane.

Types

TypeRivet sizes, inches (mm)How it cuts
Rotary hand cutter3/32 to 3/16 (2.4 to 4.8)Rivet in its hole, shims under the head, squeezed like pliers; the discs turn and shear the shank
Bench cutter3/32 to 3/16 (2.4 to 4.8) and upHeld in a vise, rivet in its hole, the handle pulled to shear the rivet
Diagonal cutting pliers—A substitute only when no cutter is at hand; the cut end is distorted and must be dressed

What to check when buying

CheckWhat to look for
Hole sizesA hole for each rivet diameter you drive, each marked with its size
Length rangeCovers the lengths you cut, with a chart on the tool
Shims or leavesAttached to the head so they cannot get lost; steps you can count
DiscsHardened, flat, tight on the pivot with no side play; a clean cut leaves no burr
HandlesA return spring and a grip that fits the hand; a bench cutter has a base for the vise
Spare partsReplacement discs and shims sold for the model

Accessories

ItemWhat it is for
6 in steel scaleMeasures the first cut rivet of a batch
Fine file or deburring toolDresses a rough cut end so it does not score the hole
Vise with soft jawsHolds a bench cutter without marking it
Parts trayKeeps cut rivets apart, marked by dash number
Light oilA drop on the pivot and the discs

Care

Blow the chips out of the holes after each batch; a chip under the head adds length.

Oil the pivot lightly and wipe the discs. Keep the shims flat and clean: a bent shim cuts every rivet short or long.

Cut only the rivets the maker lists for the tool. Replace the discs when the cut starts to leave a burr.

Safety

Wear eye protection. The cut-off end can fly out of the lower disc.

Keep fingers clear of the discs while squeezing, and clamp a bench cutter in a vise before pulling the handle.

Questions people actually ask

How do I cut a rivet to the right length?

Work out L = grip + 1.5D, put the rivet in the hole for its diameter, set the shims for that length from the chart on the tool, and squeeze. Measure the first one.

What does the dash number on a rivet mean?

The length in sixteenths of an inch: -4 is 1/4 in (6.4 mm), -5 is 5/16 in (7.9 mm), -6 is 3/8 in (9.5 mm), -7 is 7/16 in (11.1 mm), -8 is 1/2 in (12.7 mm).

Can I cut a rivet with pliers?

Diagonal cutting pliers are a substitute when no rivet cutter is at hand. They leave a distorted end, which is dressed square before the rivet goes in.

Is a cut rivet still the same part?

Only the length changes: alloy, head and diameter stay the rivet the repair data names. Use a cut rivet only where the data allows that rivet in that length.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close