Countersink Cutters and Stop Cages: Parts, Angles and Pilots

A countersink cutter cuts the cone that lets a flush head sit level with the skin; the stop cage sets how deep it goes and holds it square. Buy cutters at the angle of the heads you install, 100° for standard flush rivets and screws, with a pilot that fits your final holes, and a micrometer stop cage that takes their 1/4-28 thread.

View PDF

What it is

Where to buy

A countersink cutter is a fluted cone. Its pilot rides in the drilled hole and keeps the cone centered; the flutes cut a well at the angle of the fastener head. The cutter screws onto the spindle of a stop cage by its threaded shank.

The micrometer stop cage is the preferred countersinking tool. The drill motor turns the spindle; the skirt rests flat on the skin and stops the cutter at a set depth, while the cage holds it square to the surface. Turning the micrometer sleeve moves the stop up or down; the lock ring holds the setting.

The depth decides the result: too shallow and the head stands proud, too deep and the head sinks below the skin, the hole loses its bearing and the sheet can be cut to a knife edge. Sheet too thin to countersink is dimpled instead.

Drawing

ITEMDESCRIPTION1DRIVE SHANK2SPINDLE3HOUSING4MICRO-SLEEVE5LOCK RING6SKIRT7CUTTER, 100°8PILOT9THREADED SHANK 1/4-2810FLUTECOUNTERSINK, PILOTED, STOP CAGESHEET 1 OF 1DWG TAP-TG-027REV ASCALE 1.5:1PILOT BY FINAL HOLEHOLEPILOT IN (MM)#400.096 (2.44)#300.1265 (3.21)#210.157 (3.99)#110.189 (4.80)F0.255 (6.48)0.002 (0.05) UNDER: TAP ADVICENOTES1.DIMENSIONS IN INCHES (MM).2.CUTTER ANGLE TO MATCH THEFASTENER HEAD: 100° IS THESTANDARD.3.CUTTER THREAD 1/4-28: CHECKIT AGAINST THE CAGE.4.SET THE DEPTH ON SCRAP OFTHE SAME STACK. SLEEVE STEPS0.001 (0.03).5.SLOW SPEED, STEADY PRESSURE,SKIRT 6 FLAT ON THE SKIN.6.REPAIR DATA GOVERNS THEDEPTH.HALF SECTIONSCALE 1.5:1BDETAIL BSCALE 4:1100°CVIEW D, CUTTERSCALE 2:1VIEW CSCALE 2:112345678910
Stop cage on a two-sheet stack, half section (items 1 to 6); detail B, the 100° cutter and its pilot in the hole (items 7 and 8); view C, the six-flute cutter from the pilot end (item 10); view D, the cutter and its 1/4-28 threaded shank (item 9). Sheet scale 1.5:1.

Types and sizes

Type or sizeRange, inches (mm)Where it fits
Piloted cutter, 100°Pilots for #40 to F holes, 0.098 to 0.257 (2.49 to 6.53)Standard flush rivets and screws: the cutter for most aircraft countersinks.
Cutter, 82° or 120°Same pilotsHeads of another angle: the cutter angle always matches the head.
Interchangeable-pilot cutterOne body, pilots by hole sizeOne cutter body for several hole sizes; check that the pilot is tight in the body.
Micrometer stop cageSteps of 0.001 (0.03); 1/4-28 cutter threadAll countersinking where the cage sits flat on the skin.
Cage with a nylon skirtSame cuttersPainted or clad skins: the skirt does not mark the finish.
Extended or offset cageCutter bodies from 3/8 (9.5)Channels, flanges and tight corners where the standard cage does not fit.
Cutter body3/8 to 3/4 (9.5 to 19.1); 1/2 (12.7) is the common sizeLarger bodies for larger heads; the body must fit inside the cage skirt.
Back countersink cutterFitted through the holeWells on the far side of a part that cannot be reached from that side.

What to check when buying

CheckWhat to look for
AngleThe angle of the heads you install: 100° for standard flush rivets and screws. Keep other angles apart and marked.
PilotOne cutter or pilot per final hole size. Check the pilot against the hole: a #10 pilot, 0.1935 in (4.91 mm), will not enter a #11 hole, 0.191 in (4.85 mm).
ThreadMost cages and cutters use a 1/4-28 thread: check the cutter against the cage before you mix sources.
Cage adjustmentClear marks in steps of 0.001 in (0.03 mm) and a lock ring that holds the setting.
SkirtFlat and square to the spindle, open enough to see the cutter and let the chips out; a nylon skirt for painted skins.
FlutesSix flutes for aluminum; a single-flute cutter for CRES; sharp edges with no chips.
ReachAn extended or offset cage only if your work has channels and flanges.

Accessories

ItemWhat it is for
Cutter setOne 100° cutter for each final hole size, in a marked case.
Spare pilotsFor interchangeable-pilot cutters: pilots wear and break first.
Test rivets and scrapA strip of the same material and thickness to set the depth before the part.
Countersink depth gaugeReads the well diameter or depth to check the setting.
Backing blockHolds thin sheet steady under the pilot.
Deburring toolCleans the hole edge on the far side after countersinking.

Care

Set the depth on scrap every time. Cut a test well in the same material and stack, drop a rivet in and adjust until the head sits flush, then lock the sleeve.

Stop the chatter. Chatter is the most common countersinking problem: use a sharp cutter, slow speed and steady, firm pressure, a well-fitted pilot, and backing behind thin sheet. If it still chatters, pilot-drill undersize, countersink, then open the hole to its final size.

Keep the cutters sharp and apart. Store each cutter in its slot; a cutter dropped on its edges or used on composites is no longer good for aluminum.

Safety

Wear eye protection. Countersinking throws fine chips.

Hold the skirt flat on the skin. A tilted cage cuts an oval well and can throw the motor sideways.

Run slow. A cutter at drilling speed chatters and heats the part.

Clear chips with a brush or low-pressure air, never with your hand.

Questions people actually ask

Which countersink angle for aircraft rivets?

100° for standard flush rivets and screws. Cutters of 82° and 120° exist for other heads: the cutter angle always matches the head.

How much under the hole is the pilot?

About 0.002 in (0.05 mm). A #30 hole, 0.1285 in (3.26 mm), takes a 0.1265 in (3.21 mm) pilot.

How deep should the countersink be?

Deep enough for the head to sit flush, no deeper. The repair data governs; see the TAP advice above for the figure some manufacturers use.

Why does my countersink chatter?

A dull cutter, high speed, light pressure, a loose pilot or thin sheet with no backing. Fix the cause in that order.

Countersink or dimple?

Countersink when the sheet is thicker than the well needs; dimple when it is too thin. The countersink or dimple calculator compares the two for your sheet and rivet.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close