Layout and Marking Tools: Squares, Scribes, Markers and Punches

Every part and every rivet row starts as a line on the sheet, and a wrong mark becomes a wrong hole. Buy a combination square, dividers, a fine-tip marker and center punches; mark aluminum with the marker, never a graphite pencil, and scribe only where the metal is cut away or drilled out.

View PDF

What it is

Where to buy

Layout tools put the lines of a part on the sheet: the cut lines of the blank, the bend lines and the rivet rows. The core is a combination square: a steel rule with a head that slides along a groove and locks anywhere on it. The square head has a 90° face and a 45° face, a level vial and a scriber stored in its foot; a center head finds the center of a round bar and a protractor head sets any angle.

Dividers transfer a measurement from the rule to the sheet and step off an even pitch. A scribe draws a fine, lasting line, but it scratches the sheet: use it only on lines that will be cut away or drilled out. Every other line on aluminum is drawn with a fine-tip marker, because the graphite of a pencil can start corrosion in the aluminum.

Punches finish the layout. A prick punch makes a light mark on a layout point, and a center punch makes a deeper dimple that holds the drill point on the mark. An automatic center punch strikes with an inner spring when you press it, so one hand holds the sheet.

Drawing

ITEMDESCRIPTION1RULE2SQUARE HEAD390° FACE445° FACE5LOCK NUT6LEVEL VIAL7SCRIBER8GROOVE9GRADUATIONSSQUARE, COMBINATIONSHEET 1 OF 1DWG TAP-TG-054REV ASCALE 1:2.27HEADSHEADSETSSQUARE90°, 45°CENTERCENTERSPROTRACTORANGLESNOTES1.MARK ALUMINUMWITH A FINEMARKER; NEVER AGRAPHITE PENCIL.2.SCRIBE ONLY WHERETHE METAL IS CUTAWAY OR DRILLEDOUT.3.LOCK THE HEADBEFORE EACH LINE.4.CHECK SQUARE:DRAW A LINE, TURNTHE SQUARE OVER,DRAW AGAIN; THELINES MUST AGREE.FRONT VIEWSCALE 0.44:1AABSECTION A-ASCALE 1.5:1DETAIL BSCALE 3:1123456789
Front view of a combination square with its square head (items 1 to 7); section A-A through the head and the rule; detail B, the graduations at the end of the rule (items 8 and 9). Sheet scale 0.44:1, section 1.5:1, detail 3:1.

Types

TypeWhere it fits
Combination squareSquare and 45° lines from an edge, depths and heights; the rule doubles as a straightedge.
Center head and protractor headCenter of a round bar; any angle from an edge.
Steel ruleMeasuring and drawing straight lines; flexible rules follow a curved skin.
DividersTransfer a measurement and step off an even pitch.
ScribeFine lines on metal that will be cut away or drilled out.
Fine-tip markerEvery line on aluminum that stays on the part.
Prick punchA light mark on a layout point.
Center punch, plain or automaticA dimple that holds the drill point on the mark.

What to check when buying

CheckWhat to look for
RuleHardened steel, graduations engraved, not printed, and readable in fractions and decimals.
HeadA head that slides smoothly and locks without moving the rule.
FacesGround 90° and 45° faces with sharp corners; the square checks true when turned over.
Heads in the setSquare, center and protractor heads if you lay out angles and round parts.
DividersHardened points and a fine adjusting screw that holds the setting.
MarkerFine tip, ink that wipes off with solvent before primer.
PunchesHardened, ground points; an automatic punch with an adjustable blow.

Accessories

ItemWhat it is for
Solvent and clean wipesRemove layout lines before primer.
Spare scriber pointsFor the square head and the scribe.
Light oilFor the rule groove and the lock nut.
Case or rackKeeps the rule straight and the points sharp.
Hole finders and edge markersLay out the rivet holes from an existing pattern.

Care

Keep the faces clean. A chip under the head throws every line off square.

Never drop a square. A drop knocks the head out of square; check it again before use.

Oil the rule lightly. A thin film keeps the groove and the graduations from rusting.

Cap the points. Keep scribes, dividers and punches capped or in a case.

Safety

Cap the scribe. An open point in a pocket stabs hands.

Wear eye protection when punching. A hardened punch can chip when struck.

Hold the sheet flat. Punch on a firm surface, never on the hand.

Questions people actually ask

Can I mark aluminum with a pencil?

No. The graphite of a pencil can start corrosion in aluminum. Use a fine-tip marker and remove the lines before primer.

When do I use a scribe?

Only on lines that will be cut away or drilled out. A scribe line is a scratch that stays in the part.

Which layout tools do I need first?

A combination square, dividers, a fine-tip marker and a center punch. Add hole finders and an edge marker for rivet work.

Prick punch or center punch?

A prick punch marks a point lightly; a center punch makes the dimple that holds the drill point.

How do I check a square?

Draw a line along the rule with the head on a straight edge, turn the square over and draw again from the same point. The lines agree when the square is true.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close