Safety Wire Pliers

Safety wire pliers lock on the wire, twist it with a pull on the knob and cut it. Buy them by size and wire capacity: common pliers take 0.020 to 0.041 in (0.51 to 1.04 mm) wire, and reversible pliers twist both ways.

View PDF

What they do

Where to buy

Safety wire pliers, also called wire twisters, combine jaws, a cutter next to the pivot and a twisting mechanism. Squeezing the handles closes the jaws on the two wires and the locking sleeve holds them shut.

Pulling the knob draws the spiral rod out of the handles and spins the pliers, which twists the wire; the knob is pushed back and pulled again until the twist reaches the next part. A return spring opens the jaws when the sleeve is released.

Reversible pliers twist in either direction, so the wire can be twisted with the lay needed for right- and left-hand runs.

The twisted run is commonly six to eight twists per inch, pulled taut, and a fresh length of wire is used for each application.

Drawing

ITEMDESCRIPTION1JAWS2CUTTER3PIVOT4HANDLE5LOCKING SLEEVE6SPIRAL ROD7KNOB8RETURN SPRING9SAFETY WIREPLIERS, SAFETY WIRESHEET 1 OF 1DWG TAP-TG-106REV ASCALE 1:2SAFETY WIREDIA, IN (MM)SPEC0.020 (0.51)MS209950.032 (0.81)MS209950.041 (1.04)MS20995CAPACITYPLIERSWIRE, INSTANDARD0.041HEAVY DUTY0.060NOTES1.SQUEEZE THEHANDLES: THESLEEVE LOCKS THEJAWS ON THE WIRE.2.PULL THE KNOB:THE SPIRAL RODSPINS THE PLIERSAND TWISTS THEWIRE.3.REVERSIBLE PLIERSTWIST BOTH WAYS.4.6 TO 8 TWISTS PERINCH, WIRE TAUT.5.FRESH WIRE FOREACH APPLICATION.BTOP VIEWSCALE 1:2DETAIL BSCALE 2:11 (25.4)VIEW C, TWISTED WIRESCALE 1:1123456789
Safety wire pliers: top view with the jaws, cutter, pivot, handles, locking sleeve, spiral rod and knob; detail B of the jaws on two wires; view C of 1 in (25.4 mm) of twisted wire.

Types and sizes

TypeSize and capacityUse
Standard pliers6, 9 or 12 in nominal; wire 0.020 to 0.041 in (0.51 to 1.04 mm)General safety wiring, twisting one way
Reversible pliers6, 9 or 12 in nominal; wire 0.020 to 0.041 in (0.51 to 1.04 mm)Twisting either way for right- and left-hand runs
Heavy duty pliersWire up to 0.060 in (1.52 mm)Heavier wire
6 inShortest of the three sizesTight places and close bolt patterns
9 inMiddle sizeGeneral use
12 inLongest of the three sizesLong reach into the structure

Common safety wire

DiameterSpecification
0.020 in (0.51 mm)MS20995
0.032 in (0.81 mm)MS20995
0.041 in (1.04 mm)MS20995

What to check when buying

CheckWhat to look for
Wire capacityCovers the wire you use; 0.020 to 0.041 in on common pliers, up to 0.060 in on heavy duty
Size6, 9 or 12 in nominal for the reach you need
ReversibleTwists both ways if you wire right- and left-hand runs
Locking sleeveLocks with one squeeze and releases cleanly; the jaws do not slip on the wire
Spiral rod and knobRod straight and smooth, knob tight; the pliers spin freely on a pull
CutterSharp, aligned edges that cut the wire square without crushing
Return springOpens the jaws fully when the sleeve is released

Accessories

ItemWhat it is for
Safety wire, MS20995Wire in the diameters the manual calls for
Wire dispenserKeeps the wire straight and clean
Diagonal cuttersRemoving old wire
Light machine oilPivot and spiral rod

Care

Put a drop of oil on the pivot and the spiral rod, and wipe off the excess. Keep the rod straight: a bent rod stops the pliers spinning.

Do not cut wire thicker than the rating; it nicks the cutter edges.

Safety

Wear eye protection: cut ends of safety wire fly. Bend the pigtail back so it cannot catch skin, gloves or wiring.

Collect the cut ends; loose wire left in the aircraft is foreign object debris.

Questions people actually ask

How do safety wire pliers twist the wire?

The jaws lock on the wire with the sleeve. Pulling the knob draws the spiral rod out of the handles and spins the pliers, twisting the wire.

Do I need reversible pliers?

They twist either way, so one pair does right- and left-hand runs. Standard pliers twist one way only.

What wire sizes do they take?

Common pliers take 0.020 to 0.041 in (0.51 to 1.04 mm). Heavy duty pliers take wire up to 0.060 in (1.52 mm).

Which size should I buy?

The 9 in is the general size; the 6 in fits tight places and the 12 in reaches further into the structure.

How many twists per inch?

Commonly six to eight twists per inch, with the wire pulled taut. See the safety wire practice pages for the full rules.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close