Temporary Sheet Fasteners: Sizes, Types and Pliers

A temporary sheet fastener holds drilled parts together, hole for hole, until the rivets go in. Choose it by the rivet size of the hole and the grip of the stack, and set the spring type with pliers that fit every size.

View PDF

What it is

Where to buy

The spring type is a body with a plunger, a spring, two stepped locks and a spreader. Pliers press the plunger: the locks slide past the spreader and close, so they pass through the hole. On release the spring pulls the plunger back, the spreader opens the locks under the far sheet and the spring pulls the sheets together. The size is the rivet diameter, stamped on the body: 3/32, 1/8, 5/32, 3/16, 1/4 and 3/8 in (2.4, 3.2, 4.0, 4.8, 6.4 and 9.5 mm).

A spring fastener keeps the holes aligned; it does not clamp hard. Where the parts must be pulled together, hex nut and wing nut types are tightened by hand or with a hex nut runner. A side-grip clamp holds the edge of a part where there is no hole, and is set with the same pliers as the spring type.

Drawing

ITEMDESCRIPTION1BODY2PLUNGER3SPRING4LOCK, STEPPED (2)5SPREADER6SHEET STACK (REF)7PLIERS, JAW8PLIERS, HANDLEFASTENER, TEMPORARY SHEET, SPRINGSHEET 1 OF 1DWG TAP-TG-024REV ASCALE 1:1COMMON COLOR CODESIZE (DRILL)COLOR3/32 (#40)SILVER1/8 (#30)COPPER5/32 (#21)BLACK3/16 (#11)BRASSREAD THE STAMPED SIZENOTES1.SIZE = RIVET DIAMETER, STAMPEDON THE BODY.2.PRESS THE PLUNGER: THE LOCKSCLOSE AND PASS THE HOLE.3.RELEASE: THE SPREADER OPENSTHE LOCKS, THE SPRING PULLSTHE SHEETS TOGETHER.4.ONE PLIERS FITS ALL SPRINGSIZES.5.KEEP THE PLIERS SQUARE TO THEHOLE.GRIPINSTALLED, SECTIONSCALE 2:1PLUNGER PRESSEDSCALE 2:1PLIERS, ELEVATIONSCALE 1:212345678
Spring-type temporary fastener in section at 2:1: installed in two drilled sheets with the locks spread under the far sheet, and with the plunger pressed and the locks closed to pass the hole; the installing pliers at 1:2 (items 1 to 8).

Types and sizes

TypeSizesUse
Spring type3/32 to 3/8 in, by rivet diameter; some lists add 1/16 inHolds drilled sheets aligned, hole for hole, while you drill and rivet.
Spring type, long gripThe same diameters; grip range marked by the makerThick stacks past the grip of the standard body.
Hex nut typeBy diameter and grip rangeMore clamp-up; turned with a hex nut runner or a wrench.
Wing nut typeBy diameter and grip rangeClamp-up by hand, no tool.
Side-grip clampBy jaw depthHolds an edge or a flange where there is no hole.
PliersOne pair for every spring sizeInstall and remove spring types and side-grip clamps.
Pneumatic installerAir toolThe same job as the pliers, for jobs with large counts.

What to check when buying

CheckWhat to look for
SizeThe rivet sizes of your work, with the size stamped on each body.
GripA grip range for the thickest stack you join.
SpringFirm, so the sheets are pulled tight; even from one fastener to the next.
LocksStraight steps that close fully when the plunger is pressed.
FinishCorrosion-resistant body, plunger and locks.
PliersTips that hold the body and press the plunger square, for every spring size; a latching jaw holds the plunger pressed.
QuantityEnough of each size to fill the largest part you drill, plus spares.

Accessories

ItemWhat it is for
Storage rack or boardFasteners kept by size and counted.
Side-grip clampsEdges and flanges without a hole.
Hex nut runnerTurning hex nut types.
Deburring toolClean holes; a burr holds the sheets apart.
Spare springs and locksWhere the maker sells them, to rebuild worn fasteners.

Care

Springs. A weak spring leaves a gap between the sheets; take that fastener out of service.

Locks. Bent or worn steps slip in the hole; replace them or the fastener.

Sealant. Clean sealant off the locks before it cures.

Pliers. Check the jaw tips for wear; worn tips let the fastener slip out.

Safety

Eyes. A spring fastener can fly out if the pliers slip. Keep the pliers square to the hole and wear safety glasses.

Fingers. Keep fingers clear of the locks and the jaw tips while the plunger is pressed.

Foreign objects. Count every fastener back before the structure is closed.

Questions people actually ask

Which size goes in which hole?

The size is the rivet diameter: 3/32 in for the #40 hole, 1/8 in for #30, 5/32 in for #21, 3/16 in for #11. See the size and color chart.

Is the color code a standard?

No. Silver for 3/32, copper for 1/8, black for 5/32 and brass for 3/16 in is common, and the colors repeat on the larger sizes. Read the stamped size.

Spring type or hex nut type?

The spring type for alignment while you drill and rivet. Hex nut or wing nut types where the parts must be pulled together harder.

Pliers or a pneumatic installer?

One pair of pliers fits every spring size. An air installer only saves the hand on jobs with large counts.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close