Drill Size per Rivet Chart

A 3/32 in rivet takes a #40 drill, 1/8 in a #30, 5/32 in a #21 and 3/16 in a #11. Those four number drills cover almost all light aircraft riveting. The chart below gives each rivet its drill, the clearance that results, the pilot drill where one is used, and the oversize step when a hole has to be repaired.

View PDF
Always inches, never millimeters. Aviation is designed and worked in inches, for historical reasons and through the conventions set then. Millimeters are a translation, added as aviation grew in Europe and other metric countries. Inch values are the official ones; every millimeter figure here is a conversion. A metric drill is not the drill the rivet hole was designed around: the nearest alternatives are in the table below.

The chart

Where to buy

The clearance column is the one worth internalising: a rivet hole is deliberately larger than the rivet, by about 0.003 to 0.004 in up to 3/16 in and by 0.007 in for the 1/4 in F drill. That gap lets the rivet go in without being driven home, and it closes when the rivet is upset and swells to fill the hole.

Rivet sizeAN dashShank ØPilot drillFinal drillFinal ØClearance
3/32"-30.0938"3/32"#400.0980"+0.0042"
1/8"-40.1250"1/8"#300.1285"+0.0035"
5/32"-50.1563"5/32"#21 (FAA) · #20 (MIL-R-47196A)0.1590" · 0.1610"+0.0027" · +0.0047"
3/16"-60.1875"3/16"#110.1910"+0.0035"
1/4"-80.2500"1/4"F0.2570"+0.0070"

Every pilot and final drill in this table is the size given in Figure 4-90 of the FAA Airframe Handbook; for the 5/32 in rivet, MIL-R-47196A Table I gives the #21 or the #20 for a hole of .156–.171 in, and both are valid. AN dash numbers give diameter in thirty-seconds of an inch: -3 is 3/32", -4 is 4/32" = 1/8", and so on.

Pilot, Clecos, final: the order of work

StepActionWhat to do
1Mark and punchCenter punch every rivet location, with a bucking bar behind the sheet so the surface does not dent (FAA-H-8083-31B p. 4-39).
2Pilot, in fractionsFirst drill a slightly undersized hole, the pilot. For rivets it is the fraction equal to the rivet: 1/8 in for a 1/8 in rivet (Fig. 4-90, p. 4-39).
3Clecos inClecos hold the drilled parts in position. Sheets not held tightly together separate while being drilled or riveted; the Cleco keeps the holes in the sheets aligned (pp. 4-28, 4-29). Common shop practice: with the Clecos in, let the parts settle and relieve any stress in the stack before the final drill.
4Final, with the numbered drillReam the pilot hole with the twist drill of the final size: #40, #30, #21, #11 or F (Fig. 4-90). Holes round, straight and free from cracks (AC 43.13-1B par. 4-58).
5Deburr and cleanRemove all burrs and drill chips before riveting (p. 4-40).
6RivetBefore driving, every hole lines up, burrs and shavings are gone and the parts are held with temporary fasteners (p. 4-40).

Oversize drills: solid rivets and CherryMAX

Solid rivets have two steps. Step 1 keeps the head and takes a shank over nominal (1/64 in in -4 and -5, 1/32 in in -6 and -8): NAS1242 for the universal head (MS20470) and NAS1241 for the 100° head (MS20426), with the shank bands of the standards. No public table gives their drill: #27, #16, #1 and L are common shop practice, each the first drill at or above the top of the shank band. Step 2 is the next size, 1/32 in larger, with that rivet's drill (FAA-H-8083-31B p. 4-44; AC 43.13-1B par. 4-57b; MIL-R-47196A par. 3.4.1). CherryMAX has an oversize of its own, 1/64 in over the nominal shank, with its own drills: the 1/8 in oversize takes the #27. The go/no-go gauge accepts the hole, not the drill: T172-4 nominal, T172-400 oversize.

RivetStandard drillOversizeOversize drillSource
Solid, 3/32 in#40Next size, 1/8 in#30FAA-H-8083-31B p. 4-44, Fig. 4-90; MIL-R-47196A Table I
Solid, 1/8 in#301/64 in over: NAS1242 / NAS1241 -4, same head, shank .140–.144 in#27, common shop practiceShank: NAS1241AD4, shank band of NAS1241 and NAS1242. No public table gives the drill.
Solid, 1/8 in#30Next size, 5/32 in#21 or #20FAA-H-8083-31B p. 4-44, Fig. 4-90; MIL-R-47196A Table I
Solid, 5/32 in#21 or #201/64 in over: NAS1242 / NAS1241 -5, same head, shank .171–.176 in#16, common shop practiceShank: NAS1242AD5, shank band of NAS1241 and NAS1242. No public table gives the drill.
Solid, 5/32 in#21 or #20Next size, 3/16 in#11FAA-H-8083-31B p. 4-44, Fig. 4-90; MIL-R-47196A Table I
Solid, 3/16 in#111/32 in over: NAS1242 / NAS1241 -6, same head, shank .218–.223 in#1, common shop practiceShank: NAS1241AD6, shank band of NAS1241 and NAS1242. The #1 is also the drill of the 7/32 in rivet (MIL-R-47196A Table I).
Solid, 1/4 inF1/32 in over: NAS1242 / NAS1241 -8, same head, shank .280–.285 inL, common shop practiceShank: NAS1242AD8, shank band of NAS1241 and NAS1242. No public table gives the drill.
CherryMAX -4, 1/8 in#30, .129–.132 inOversize, 1/64 in over#27, .143–.146 inThe Aviation Point data
CherryMAX -5, 5/32 in#20, .160–.164 inOversize#16, .176–.180 inAs above
CherryMAX -6, 3/16 in#10, .192–.196 inOversize#5, .205–.209 inAs above
CherryMAX -8, 1/4 inF, .256–.261 inOversizeI, .271–.275 inAs above

Solid 3/16 and 1/4 in: the next size, 7/32 or 9/32 in, is not in Fig. 4-90; the drawing or the SRM gives its drill. A larger rivet needs more edge distance and pitch: check both again. Bulbed CherryLOCK uses #27, #16 and #5 as its normal drills.

Hi-Lok, Jo-Bolt, blind bolts and bolts: standard and oversize holes

Each fastener family has its own oversize: 1/64 in for Hi-Lok, Jo-Bolt, Visu-Lok and CherryLOCK, and 1/32 in as a second step for Hi-Lok only. The oversize pin or bolt keeps the first dash of the one it replaces. Precision bands of 0.001 in are reamed, not drilled. Hole bands, then drills that fall inside them.

FastenerSizeStandard hole1st oversize, 1/64 in2nd oversize, 1/32 inSource
Hi-Lok, clearance (column A)-5, 5/32 inReam .1635–.1645 inNone: use the -6 pinNone: use the 1/64 in -6 pinNAS618 sheets 3, 6, 7; Hi-Shear HL19, HL63, HL219
Hi-Lok-6, 3/16 inReam .1895–.1905 inReam .2026–.2036 inReam .2182–.2192 inAs above
Hi-Lok-8, 1/4 inReam .2495–.2505 inReam .2651–.2661 inReam .2807–.2817 inAs above
Hi-Lok-10, 5/16 inReam .312–.313 inReam .3276–.3286 inReam .3432–.3442 inAs above
Hi-Lok-12, 3/8 inReam .3745–.3755 inReam .3901–.3911 inReam .4057–.4067 inAs above
Hi-Lok-14, 7/16 inReam .437–.438 inReam .4526–.4536 inReam .4682–.4692 inAs above
Hi-Lok-16, 1/2 inReam .4995–.5005 inReam .5151–.5161 inReam .5307–.5317 inAs above
Jo-Bolt and Visu-Lok (Monogram)-08, 5/32 in#19, .165–.168 in#15, .180–.183 inNone (no public number)Monogram PLT110, PLT111 (figures); FAA-H-8083-31B fig. 4-47 drills
Jo-Bolt and Visu-Lok-3, 3/16 in#8, .199–.202 inDrill under and ream, .215–.218 inNoneAs above
Jo-Bolt and Visu-Lok-4, 1/4 inG, .260–.263 inJ, .276–.279 inNoneAs above
Jo-Bolt and Visu-Lok-5, 5/16 in5/16, .312–.315 in21/64, .327–.330 inNoneAs above
Jo-Bolt and Visu-Lok-6, 3/8 in3/8, .375–.378 in25/64, .390–.393 inNoneAs above
CherryLOCK-3, 3/32 in#40, .097–.100 inNone in the tableNoneThe Aviation Point data; TM 1-1500-204-23-6 fig. 2-56
CherryLOCK-4, 1/8 in#30, .129–.132 in#27, .143–.146 inNoneAs above
CherryLOCK-5, 5/32 in#20, .160–.164 in#16, .176–.180 inNoneAs above
CherryLOCK-6, 3/16 in#10, .192–.196 in#5, .205–.209 inNoneAs above
CherryLOCK-8, 1/4 inF, .256–.261 inNone in the tableNoneAs above
AN boltAN4, 1/4 inFNext bolt size: O—TM 1-1500-204-23-6 par. 2-2r; FAA-H-8083-31B fig. 4-47
AN boltAN5, 5/16 inONext bolt size: V—As above
AN boltAN6, 3/8 inVNext bolt size, per the drawing—As above

Hi-Lok: column A is the clearance fit for steel, titanium and composite (FAA-H-8083-31B p. 4-50). In aluminum the fit is interference, not over 0.002 in, and the drawing sets the hole; see the Hi-Lok holes guide. Screws, close-tolerance bolts, Maxibolt and Composi-Lok: the hole is on the drawing or in the fastener standard. The SRM, the drawing or the approved repair data governs over every row.

Metric alternatives, solid rivets

For solid rivets: nearest metric alternative, commonly used where inch drills cannot be bought. NOT the official drill. A metric drill is not the drill the rivet hole was designed around. The inch drill is the official one; this table is for where it cannot be bought.

Official drillUsed forInches (official)Exact mmNearest metric alternative, mmDifference, mm
3/32 inWork, 3/32 rivet0.09375 in2.3812.40+0.019
#40Final, 3/32 rivet0.0980 in2.4892.50+0.011
1/8 inWork, 1/8 rivet0.1250 in3.1753.15 or 3.20−0.025 or +0.025
#30Final, 1/8 rivet0.1285 in3.2643.25−0.014
5/32 inWork, 5/32 rivet0.15625 in3.9693.95−0.019
#21Final, 5/32 rivet0.1590 in4.0394.05+0.011
#20Final, 5/32 rivet (MIL-R-47196A)0.1610 in4.0894.10+0.011
3/16 inWork, 3/16 rivet0.1875 in4.7634.75−0.013
#11Final, 3/16 rivet0.1910 in4.8514.85−0.001
1/4 inWork, 1/4 rivet0.2500 in6.3506.350.000
FFinal, 1/4 rivet0.2570 in6.5286.55+0.022

Exact mm = inches × 25.4. The alternative is the nearest size on a 0.05 mm step; the difference is that size minus the exact size. 1/8 in falls exactly halfway, so both neighbors are shown: neither equals 1/8 in. For a #30 solid-rivet hole, 3.25 mm is −0.014 mm and 3.30 mm is +0.036 mm. This table is for solid rivets; for CherryMAX and CherryLOCK the maker's hole range decides (see Metric alternatives for blind rivets). This table approves no hole: the tolerance is set by the manual (SRM, AMM or drawing).

Metric alternatives for blind rivets

For CherryMAX and CherryLOCK the metric drill is chosen inside the maker's hole range, not by nearest size. Cherry gives a minimum and a maximum hole; a metric drill whose size falls outside it is not offered here. Not the official drill.

Official drillUsed forMaker's hole range, inMetric inside the range, mm= inchesNearest metric, mm
#40CherryLOCK 3/32 in0.097 to 0.1002.500.09842.50 (inside)
#30CherryMAX / CherryLOCK -4 (1/8 in)0.129 to 0.1323.300.12993.25 (outside)
#20-5 (5/32 in)0.160 to 0.1644.100.16144.10 (inside)
#10-6 (3/16 in)0.192 to 0.1964.900.19294.90 (inside)
F-8 (1/4 in)0.256 to 0.2616.550.25796.55 (inside)
#27-4 oversize / bulbed0.143 to 0.1463.650.14373.65 (inside)
#16-5 oversize / bulbed0.176 to 0.1804.500.17724.50 (inside)
#5-6 oversize / bulbed0.205 to 0.2095.250.20675.20 (outside)
I-8 oversize0.271 to 0.2756.900.27176.90 (inside)

Limits: The Aviation Point data. Metric sizes are on a 0.05 mm step, chosen as the nearest to the official drill that lies inside the maker's range; mm and inches are conversions. For solid rivets use the table above (nearest size). A go/no-go gage decides the hole. The calculator drill for part number gives the same figures. This table approves no hole: the SRM or drawing comes first.

On pilot drills — shop practice, not FAA data. The pilot column above is Figure 4-90's fractional drill: you work with it, and pass the number drill in the last step before riveting. Drilling #41 before #40, or #31 before #30, is widespread practice among kit builders and it works: the undersize pass locates the hole and the final pass cleans it round. But be clear about its standing — neither AC 43.13-1B nor the FAA Airframe Handbook names #41 or #31 as pilot drills. What the Handbook actually says is the opposite direction of travel: “the procedure for drilling holes larger than 3/16 inch in sheet metal is to drill a pilot hole with a No. 40 or No. 30 drill bit and then to oversize with a larger drill bit to the correct size.” Use the two-step sequence if it suits your work; do not cite a regulator for it.

Alternates you will see quoted, and what they are for

Four other number drills turn up constantly in catalogs and forum threads. None of them is wrong — each has a job.

DrillDiameterRelative toWhat it is for
#410.0960"0.002" under #40Common shop-practice pilot ahead of #40. Not named as such in either FAA source.
#310.1200"0.005" under 1/8"Same practice ahead of #30. Undersize even of the rivet, so never rivet into it.
#200.1610"0.002" over #21Quoted for 5/32" clecos. A cleco only has to fit the hole, not fill it to rivet tolerance.
#100.1935"0.0025" over #11Quoted for 3/16" clecos, for the same reason.

Drill your rivet holes to the standard in the main chart. The cleco will still fit — that is the direction the tolerance runs.

The oversize repair sequence

When a hole is enlarged, elongated or damaged during rivet removal, the standard remedy is to go up one rivet size and re-drill to that rivet's drill. The sequence runs 3/32 → 1/8 → 5/32 → 3/16, each 1/32 in larger, and each step takes the drill from the row below it in the main chart; above 3/16 in the next size is 7/32 in, which the chart does not cover. The oversize drills are in the table above.

Two things constrain this and both are easy to forget. First, edge distance is a function of diameter — going up a size increases the required edge distance by the same proportion, so a hole that was marginal on edge distance gets worse, not better. Second, the surrounding pattern was designed for the original size: pitch minimums scale with D as well.

In practice the oversize step is a legitimate and common technique, but it is a repair decision made against approved data, not a shop-floor reflex. Check the SRM. Some structures permit one oversize step and no more; some permit none.

Note also that an oversize repair changes the part callout. A hole taken from #30 to #21 now needs a 5/32" rivet — a different diameter code, a different length requirement, and a shop head 1.5 × 0.156" across rather than 1.5 × 0.125".

Drilling practice that actually affects the hole

Use a drill made for aluminum. A standard 118° jobber bit tends to grab and tear in thin soft alloy. Aircraft sheet metal bits are commonly ground at 135° with a split point, which centers without a punch and cuts rather than pushes.

Speed high, feed light. Aluminum likes a fast spindle and a gentle constant pressure. Leaning on the drill produces a triangular hole and a burr you will spend longer removing than you saved.

Back the sheet up. Drilling unsupported sheet lets it flex away from the bit and leaves a dished, oversized exit. A backing block behind the work is the difference between a round hole and an approximately round hole.

Deburr both sides, every hole. The burr on the exit side holds the sheets apart, and a joint riveted over burrs is a joint with a gap in it. This is the step most often skipped and most visible in the finished work.

Check the hole, not the drill. A worn or badly sharpened bit cuts oversize. If rivets are loose in freshly drilled holes, measure the hole before blaming the rivets.

Worked example

Match-drilling a 1/8" rivet line through two sheets of 0.032" 2024-T3.

  1. Pilot the run at 1/8" (0.1250") through both sheets clamped together, as Figure 4-90 gives it.
  2. Cleco every third hole as you go — copper clecos for 1/8".
  3. Open each hole to final size with #30 (0.1285"), backing the sheet.
  4. The finished hole is 0.0035" larger than the 0.1250" rivet shank. That clearance is what lets the rivet drop in cleanly.
  5. Deburr both faces of both sheets, separate, clean, and reassemble to rivet.
  6. The rivet swells as it is driven and fills the 0.0035". A correctly driven rivet has no clearance left.

#31 then #30. The clearance is designed in, not a tolerance you are fighting.

Where the sources agree, and where they do not

PointFirst sourceSecond sourceWhere they differ, and what governs
Enlarged holeHandbook p. 4-44, Fig. 4-90: next rivet size, next drill (1/8 in #30, then 5/32 in #21 or #20)AC 43.13-1B par. 4-57: an enlarged or damaged hole is drilled or reamed for the next larger rivet, edge distance and spacing kept above the minimumAgree. The AC adds the edge distance check on the larger rivet.
Edge distance after the oversizeAC 43.13-1B par. 4-57c: single row, edge distance not less than 2 diameters, spacing not less than 3Handbook pp. 4-34 and 4-35: 2 diameters universal, 2-1/2 countersunkFor countersunk rivets the Handbook's 2-1/2 diameters is the stricter and governs.
Hole qualityAC 43.13-1B par. 4-58: round, straight, free of cracks, deburredHandbook p. 4-40: burr remover or larger drill bitAgree.
5/32 in rivetHandbook p. 4-44: #21MIL-R-47196A Table I: #20One number apart; see the rows above for which governs.

Questions people actually ask

What drill size for an AN470AD4 rivet?

#30, which measures 0.1285". AN470AD4 is a 1/8" (4/32") diameter rivet, and 0.1285" gives the standard 0.0035" clearance.

What drill for a 3/32 rivet?

#40 (0.0980") as the final size, with a 3/32" pilot per Figure 4-90.

Why is the hole bigger than the rivet?

So the rivet can be inserted without being forced. The clearance is about 0.003 to 0.004 in up to 3/16 in and 0.007 in on the 1/4 in F drill, and it disappears when the rivet is driven — the shank swells under the bucking bar and fills the hole completely. A rivet that fits tightly before driving cannot swell to fill anything.

Can I use a 1/8" drill instead of a #30?

No. A 1/8" drill measures 0.1250", identical to the rivet shank, leaving zero clearance. The rivet will not go in cleanly, and forcing it damages both the hole and the shank. #30 exists precisely because 1/8" is the wrong size for a 1/8" rivet hole.

What is the difference between #40 and #41?

Twenty ten-thousandths of an inch: #41 is 0.0960", #40 is 0.0980". #41 is the undersize pilot; #40 is the final size for a 3/32" rivet.

My rivets are loose in the holes. Wrong drill?

Possibly, but check the drill itself before the chart. A worn or asymmetrically sharpened bit cuts well over its nominal size. Measure a finished hole with pin gauges or callipers and compare against the drill Ø column above.

Limits — when NOT to use this chart

Standard hole sizes for solid aluminum rivets in sheet metal.

  • Approved data governs. The SRM, AMM or repair drawing specifies the hole. Where it differs from this chart, it wins.
  • Blind and special fasteners have their own hole sizes. CherryMAX, Hi-Lok, lockbolts and Jo-Bolts are drilled and often reamed to the manufacturer's published dimensions, which are tighter and are not the drills in this chart.
  • Interference-fit and reamed applications are different. Some structures call for a reamed hole to a tighter tolerance than a drill alone can hold. Drilling to size and stopping is not equivalent.
  • Not for composites. Hole preparation in laminates involves different geometry, different tooling and delamination control at breakout.
  • Oversize repair is a design decision. Going up a size changes edge distance and pitch requirements — see above.
  • Drill wear defeats the chart. A worn bit cuts oversize regardless of what is stamped on it. Measure the hole on anything that matters.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Main sources

  • FAA-H-8083-31, AMT Handbook — Airframe, Volume 1, Figure 4-90 — “Drill sizes for standard rivets” — the source of every drill and decimal in the main table above, plus drilling practice and deburring.
  • FAA AC 43.13-1B CHG 1, Chapter 4 — hole preparation in the context of riveting. Note it does not carry the per-rivet drill table — that is the Handbook's.
  • ANSI/ASME B94.11M number drill series — decimal diameters for number drills quoted in the tables above.
  • FAA-H-8083-31B (2023), AMT Handbook — Airframe, Chapter 4 — p. 4-39, Fig. 4-90 and the pilot then final drilling; pp. 4-28, 4-29, Clecos; p. 4-40, deburring and driving; p. 4-44, the next larger size, 1/32 in greater.
  • The Aviation Point data — CherryMAX drills and hole sizes, nominal and oversize, and the T172 gauges.
  • MIL-R-47196A(MI), Rivets, Buck Type, Preparation for and Installation of (6 September 1977) — Table I, hole sizes for standard rivets: 5/32 in takes the #21 or the #20, hole .156–.171 in; par. 3.4.1, the next larger rivet size.
  • FAA AC 43.13-1B CHG 1, Acceptable Methods, Techniques, and Practices: Aircraft Inspection and Repair — Par. 4-57, 4-57c and 4-58.
  • NAS1241 and NAS1242, Rivets, Solid, Oversize Repair — Shank diameter bands of the oversize rivets.

Cross-checked with other manuals and standards in our library.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close