Inspection Gauges: Rivet, Thickness, Drill and Radius Gauges

A gauge answers one question fast: is it the right size? A rivet shop head gauge checks a driven head against 1.5D wide and 0.5D high; thickness, drill, radius and thread gauges name a size before a measuring tool confirms it.

View PDF

What they check

Where to buy

An inspection gauge compares, it does not measure: a slot, a step, a leaf or a hole of known size held against the work. It is quicker than a caliper and reads the same in every hand.

The rivet shop head gauge checks the bucked head of a solid rivet. The handbooks call for a shop head about 1.5 times the shank diameter (1.5D) wide and 0.5D high; the gauge carries a slot and a step for each rivet size.

Thickness, drill, radius, thread pitch and feeler gauges name a size at a glance. When a reading decides a repair, confirm it with a micrometer or a caliper.

Drawing

ITEMDESCRIPTION1GAUGE PLATE2DIAMETER SLOT, 1.5D3HEIGHT STEP, 0.5D4HANGING HOLE5SHOP HEAD6RIVET SHANK7FACTORY HEAD8SKINSGAUGE, RIVET SHOP HEADSHEET 1 OF 1DWG TAP-TG-056REV ASCALE 1.3:1HEAD DIA, 1.5DRIVETIN (MM)3/32.141 (3.6)1/8.188 (4.8)5/32.234 (5.9)3/16.281 (7.1)1/4.375 (9.5)HEAD HEIGHT, 0.5DRIVETIN (MM)3/32.047 (1.2)1/8.063 (1.6)5/32.078 (2.0)3/16.094 (2.4)1/4.125 (3.2)NOTES1.INCHES (MM).2.HEAD MUST NOT PASSITS SLOT.3.HEAD MUST TOUCH ITSSTEP.4.REPAIR DATA GOVERNS.3/321/85/323/161/4FRONT VIEWSCALE 1.3:1BDETAIL B, ON A 1/8 RIVETSCALE 4:1.063 (1.6)C.188 (4.8)DETAIL C, SLOT ON THE HEADSCALE 3:112345678
Rivet shop head gauge: a diameter slot and a height step for each rivet size, detail B of the step on a driven 1/8 in rivet and detail C of the slot over the head.

Types and sizes

TypeSize or range, inches (mm)Where it fits
Rivet shop head gaugeA slot and a step for each rivet, 3/32 to 1/4 (2.4 to 6.4)Diameter and height of driven heads, after riveting
Sheet thickness gaugeNotches marked in gauge numbers and decimal inchesSorting sheet stock; confirm with a micrometer
Drill gaugeHoles for number, letter and fraction drills, 1/16 to 1/2 (1.6 to 12.7)Naming a drill bit before it goes in the motor
Radius gaugeInside and outside leaves, 1/32 to 1/2 (0.8 to 12.7)Bend radius of formed parts, flanges and fillets
Thread pitch gaugeLeaves in threads per inch and in metric pitchNaming bolt, screw and nut threads
Feeler gaugeLeaves from .0015 to .025 (0.04 to 0.64)Gaps between parts and shims at fit-up
Flushness gaugeDial indicator on a three-point base, reads .001 (0.025)Head height of flush rivets and countersink depth
Inspection magnifier5x to 10x, with or without a lightSuspected cracks at holes, heads and edges

What to check when buying

CheckWhat to look for
MarkingsSize stamped or etched at every slot, hole and leaf, in inches and in mm where the gauge carries both
MaterialHardened or stainless steel; leaves that spring back flat
Gauging edgesSquare and sharp, no burrs, no wear at the slots and steps
Rivet gauge rangeA slot and a step for each rivet size you drive, 3/32 to 1/4 in
Drill gaugeNumber, letter and fraction sizes on one plate, each hole marked with its decimal
Leaf holderA screw that locks the leaves; leaves sold one by one
Flushness gaugeThree-point base, a dial that reads .001 in, a point that reaches the head
CalibrationGauges that decide acceptance go in the shop calibration list, with a serial number

Accessories

ItemWhat it is for
Inspection mirrorThe back of a joint and the shop heads you cannot see
FlashlightRaking light across the skin shows dents, heads and cracks
MarkerMarks a head that fails the gauge for drilling out
Case or pouchKeeps plates and leaves flat and apart
Light oilA thin coat against corrosion on steel leaves

Care

Keep the gauging edges sharp. Never use a gauge plate as a scraper, a screwdriver or a pry; a rounded slot passes heads under size.

Wipe and oil steel leaves after use and fold them back into the holder. Replace a kinked or rusted leaf: it no longer reads its size.

Check the gauges against a micrometer or a gauge block at the shop calibration interval, and after a drop.

Safety

Feeler and radius leaves are thin and sharp. Hold them by the holder, never slide a finger along an edge.

Never gauge a turning part. Stop the drill or the machine before a gauge goes near it.

Questions people actually ask

How does a rivet shop head gauge work?

Each rivet size has a slot as wide as 1.5D and a step as high as 0.5D. Slide the slot over the driven head: the head must not pass through. Stand the step next to the head on the skin: the head must reach its ceiling.

What if a shop head fails the gauge?

A head that is too tall can take a little more driving. A head that is too flat, cracked or off center is drilled out and the rivet replaced, as the repair data says.

Thickness gauge or micrometer for sheet?

The gauge sorts stock quickly; the micrometer gives the number. Use the micrometer when the thickness decides a repair or an order.

Does a drill gauge check a hole?

No: it names a drill bit. A hole is checked with a pin gauge or a hole gauge of the right size, or with the fastener itself.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close