Hand Forming Tools

Hand forming tools curve, bump, shrink and stretch sheet where a brake or a slip roll cannot reach. Use soft faces on aluminum, support the sheet on a sandbag, stake or form block, and buy shrinkers and stretchers by their sheet capacity.

View PDF

What they do

Where to buy

Soft-faced mallets of rawhide, plastic or rubber form aluminum without marring or stretching it. A rawhide face is a roll of hide; it is trimmed back when it wears.

Bumping forms a dish or a compound curve by hammering the sheet into a hollow. On a sandbag of canvas or leather filled with sand, the sheet is worked with light glancing blows of a round-faced mallet, from the edge toward the center.

Stakes and dollies back the sheet from below while it is shaped. Form blocks, commonly of hardwood, give the exact contour of a rib or flange, and a V-block supports curved flanges as they are worked.

Shrinkers and stretchers grip the flange between jaws and move them together or apart. Shrinking the flange of an angle curves it with the flange on the inside; stretching curves it with the flange on the outside.

Drawing

ITEMDESCRIPTION1MALLET HEAD, RAWHIDE2HANDLE3FACE, ROLLED RAWHIDE4UPPER JAWS5LOWER JAWS6FLANGE7SANDBAG8SAND9SHEET10BUMPING MALLETTOOLS, HAND FORMINGSHEET 1 OF 1DWG TAP-TG-099REV ASCALE 1:3SHRINKER CAPACITYSHEETGAUGE (IN)MILD STEEL18 GA (0.048)ALUMINUM16 GAMALLET FACESFACEUSERAWHIDEFORMINGPLASTICFORMINGRUBBERLIGHT WORKNOTES1.SOFT-FACED MALLETSFORM WITHOUT MARRINGTHE SHEET.2.SHRINK THE FLANGE: ITCURVES TO THE INSIDE.3.STRETCH THE FLANGE: ITCURVES TO THE OUTSIDE.4.BUMP ON THE SANDBAGWITH LIGHT GLANCINGBLOWS.5.SEVERE FORMING:ANNEALED SHEET.SIDE VIEW, RAWHIDE MALLETSCALE 1:3VIEW BSCALE 1:3VIEW C, SHRINKER JAWS ON THE FLANGESCALE 1:1SECTION D, BUMPING ON A SANDBAGSCALE 1:312345678910
Rawhide mallet with the face of rolled hide; shrinker jaws gripping a flange; a sheet bumped on a sandbag with a round-faced mallet.

Types

ToolWhat it isUse
Rawhide malletHead of rolled hide on a wooden handleGeneral forming of aluminum without marks
Plastic-faced malletReplaceable plastic faces on a metal or wooden headForming and flattening; faces changed when worn
Rubber malletSolid rubber headLight work and setting parts in place
Bumping malletRound or teardrop faceDishes and compound curves on a sandbag
SandbagCanvas or leather bag filled with sandSupport for bumping
Stakes and dolliesSteel shapes held in a vise or in the handBacking the sheet while it is shaped
Form block and V-blockHardwood or metal block cut to the contourRibs, flanges and curved angles
Shrinker and stretcherPairs of gripping jaws worked by a leverCurving flanges and angles

What to check when buying

CheckWhat to look for
Mallet facesRawhide, plastic or rubber, with no metal edge that can touch the sheet
Face conditionSmooth and clean; trim or replace a face that is chipped or has grit in it
SandbagStrong canvas or leather with tight seams, filled firm with clean sand
Stakes and dolliesPolished faces free of nicks; any mark on a face prints on the sheet
Shrinker and stretcher capacityCommonly 18 gauge, 0.048 in (1.22 mm) mild steel and 16 gauge aluminum; check the plate
Shrinker and stretcher jawsReplaceable jaw sets that close square and grip without slipping
MountingBench or vise mounting that stays still under the lever

Accessories

ItemWhat it is for
Templates and radius gaugesChecking the contour while forming
Spare jaw setsReplacing worn shrinker and stretcher jaws
Spare mallet facesReplacing worn plastic faces
Files and abrasive padsSmoothing jaw marks and edges
Bench vise with soft jawsHolding stakes, form blocks and parts

Care

Keep mallet faces, stakes and dollies clean and smooth, and store them where they cannot pick up grit or steel chips. Trim a rawhide face square when it frays.

Clean shrinker and stretcher jaws with a stiff brush; aluminum pick-up on the teeth makes them slip and mark the flange.

Safety

Wear eye protection when bumping and hammering. Sheet edges are sharp; deburr them before forming and wear gloves to handle the part.

Keep fingers clear of the jaws and the lever of a shrinker or stretcher.

Questions people actually ask

Why use a soft-faced mallet on aluminum?

Rawhide, plastic and rubber faces form the sheet without marring or stretching it. A steel hammer leaves marks that can start cracks.

Which way does a shrunk flange curve?

Shrinking the flange of an angle curves it with the flange on the inside of the curve. Stretching the flange curves it with the flange on the outside.

What is a sandbag for?

It supports the sheet while it is bumped into a dish or a compound curve. Work with light glancing blows of a round-faced mallet.

What capacity do shrinkers and stretchers have?

Common hand units take 18 gauge, 0.048 in (1.22 mm) mild steel and 16 gauge aluminum. Check the plate on the tool.

Can every alloy be hand formed?

Severe forming is done with the sheet in an annealed temper and then heat treated as the drawing or the approved repair data states.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close