Blind Rivet Tools: Pullers, Nosepieces and Pulling Heads

A blind rivet tool grips the stem and pulls it while its nose holds the rivet head down, so the blind head forms on the far side. The pulling head must match the rivet family, diameter and head style, so choose the tool by the heads available for the rivets you install.

View PDF

What it is

Where to buy

A blind rivet goes in from one side. The tool slips its nosepiece or pulling head over the stem and holds the rivet head down; jaws in a tapered jaw case grip the stem and pull it. The stem draws the end of the sleeve into a blind head on the far side, the sheets are pulled together and the stem breaks. Seat the head with firm, steady pressure, then pull, and hold the tool square until the stem breaks.

There are two families. In a friction-lock rivet the stem is held by friction only and does not break flush; trim it and file it flush. In a mechanical-lock rivet a lock collar locks the stem to the sleeve and the stem breaks at its notch; never file a locked stem, it weakens the lock. The rivet length comes from the grip, the thickness of the sheets. Blind rivets go in structure only where the repair data allows them.

Drawing

ITEMDESCRIPTION1NOSEPIECE2JAW CASE3JAWS4JAW SPRING5HANDLE, FIXED6HANDLE, LEVER7STEM8SLEEVE9LOCK COLLARTOOL, HAND, BLIND RIVET, PULL TYPESHEET 1 OF 1DWG TAP-TG-078REV ASCALE 1:1STEM AFTER THE PULLLOCKSTEMFRICTIONTRIM, FILE FLUSHMECHANICALBREAKS AT NOTCHNEVER FILE A LOCKED STEMNOTES1.PULLING HEAD BY RIVET DIAMETERAND HEAD STYLE.2.RIVET LENGTH FROM THE GRIP.3.SEAT THE HEAD WITH FIRM, STEADYPRESSURE, THEN PULL.4.HOLD THE TOOL SQUARE UNTIL THESTEM BREAKS.5.BLIND RIVETS ONLY WHERE THEREPAIR DATA ALLOWS.HAND TOOL, ELEVATIONSCALE 1:2HEAD, SECTIONSCALE 2:1GRIPMECHANICAL LOCK, INSTALLEDSCALE 4:1123456789
Hand blind rivet tool in elevation at 1:2; its head in section at 2:1 with the nosepiece, the jaw case, the jaws gripping the stem and the jaw spring; a mechanical-lock blind rivet installed in two sheets in section at 4:1, with the lock collar and the stem broken flush (items 1 to 9).

Types and sizes

TypeTakesUse
Hand riveter (pliers type)Pull-stem rivets, by nosepieceField work and short runs.
Lever riveter (long handles)Larger diameters and harder stems, by nosepieceMore pull for less hand force.
Pneumatic or hydraulic pullerBy pulling headProduction work and most mechanical-lock rivets.
NosepieceOne per rivet diameterHolds the head down and lets the stem into the jaws.
Pulling headBy rivet family, diameter and head styleMatches a power tool to a mechanical-lock rivet, protruding or flush head.
Grip gaugeBy rivet familyMeasures the stack, so the rivet length suits the grip.

What to check when buying

CheckWhat to look for
CapacityThe rivet diameters and stem materials the tool is rated for, stated by the maker.
HeadsNosepieces or pulling heads for every diameter and head style you install.
StrokeLong enough to break the stem of the longest grip you install in one pull.
JawsHardened and replaceable, sold as spares.
Stem handlingA stem collector or a clear path out, so stems do not fall into the structure.
Power toolsWeight and balance in the hand, air pressure stated by the maker, a trigger that holds until the stem breaks.

Accessories

ItemWhat it is for
Nosepiece setOne per rivet diameter.
Pulling headsMechanical-lock rivets by family, diameter and head style.
Grip gaugeThe rivet length for the stack.
Spare jaws and jaw springWorn jaws let the stem slip.
Stem collectorKeeps broken stems out of the structure.
Feeler gauge 0.005 inChecks that the head is tight.

Care

Jaws. Clean chips out of the jaw teeth and the jaw case; worn teeth let the stem slip.

Nosepiece. A worn or burred bore marks the head and can hold the stem; replace it.

Power tools. Keep the air clean and dry and lubricate as the maker states; check the hydraulic oil level where there is one.

Safety

Eyes. A broken stem can fly out of the back of the tool. Wear safety glasses.

Hands. Keep fingers clear of the handles and the nose during the pull.

Foreign objects. Collect every broken stem; one left in a closed structure is foreign object.

Questions people actually ask

Hand riveter or pneumatic puller?

A hand riveter for field work and friction-lock rivets. Mechanical-lock structural rivets are normally set with a power tool and the pulling head for their part number.

Which pulling head do I need?

The one for the rivet family, diameter and head style. The pulling head selector finds it from the part number, and Pulling heads by part number lists them.

May a blind rivet replace a solid rivet?

Only where the repair data allows it. See blind fasteners.

Why is the stem not flush?

A friction-lock stem is trimmed and filed flush. A mechanical-lock stem breaks at its notch; a stem standing proud usually means the wrong grip or a worn pulling head.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close