Step Drills, Hole Saws and Hole Punches

Large holes in thin sheet, for access, wiring, tubes and lightening, need a different tool than a rivet hole. A step drill for up to 3/4 in, a hole saw or a punch above that, and a twist drill for every fastener hole.

View PDF

What it does

Where to buy

A step drill is one hardened cone of cylindrical steps. Its pilot point drills the first hole and each step opens it by a fixed amount, commonly 1/32 in (0.8 mm) on the diameter, 1/64 in (0.4 mm) a side, on the 1/8 to 1/2 in bit and 1/16 in (1.6 mm) on the 1/4 to 3/4 in bit. It works best in soft metals and very thin sheet, and a step can also deburr a hole left by another bit.

A hole saw is a toothed steel cup on an arbor, with a pilot drill in the center. Saws from 9/16 to 1-3/16 in fit the 1/2-20 arbor; 1-1/4 in and up fit the 5/8-18 arbor.

A hole punch pulls a punch through the sheet into a die with a draw screw: no chips, no spinning tool. A fly cutter cuts any diameter but only in a drill press.

Lightening holes are cut with a hole saw, a punch or a fly cutter, the edge filed smooth so it cannot start a crack, then flanged for stiffness. They are never cut in a structural part unless the approved data calls for them.

Drawing

ITEMDESCRIPTION1SHANK, 3 FLATS2PILOT POINT3STEP4FLUTE5STEP BEVEL6HOLE SAW CUP7TEETH8ARBOR9PILOT DRILL10PUNCH11DIE12DRAW SCREW13SHEETTOOLS, LARGE HOLESHEET 1 OF 1DWG TAP-TG-059REV ASCALE 1.8:1STEP DRILLSRANGE INSTEP1/8-1/21/321/4-3/41/1613 AND 9 HOLESHOLE SAW ARBORTHREADSAWS IN1/2-209/16-1 3/165/8-181 1/4 AND UPNOTES1.DIMENSIONS ININCHES (MM).2.STEP DRILL: PILOTPOINT FIRST, STOPON THE STEP FORTHE SIZE.3.STEP DRILLS: SOFTMETALS AND THINSHEET.4.CLAMP THE SHEETAND BACK IT WITHWOOD.5.LIGHTENING HOLES:FILE THE EDGESMOOTH.AA1/8 (3.2)1/2 (12.7)SIDE VIEW, STEP DRILLSCALE 1.8:1B1/64 (0.4)DETAIL BSCALE 6:1SECTION A-ASCALE 3:1VIEW D, PUNCH AND DIE, IN SECTIONSCALE 1:11 1/4 (31.8)VIEW C, HOLE SAW, HALF SECTIONSCALE 1:112345678910111213
Step drill 1/8 to 1/2 in by 1/32 in: side view with the pilot point, steps, flute and three-flat shank, detail B of the steps and section A-A through the flute; a 1-1/4 in hole saw on its arbor in half section; a punch and die on the sheet in section.

Types and sizes

TypeSize, inches (mm)Use
Step drill, 1/32 in steps1/8 to 1/2 (3.2 to 12.7), 13 holesHoles between drill sizes in thin sheet; deburring
Step drill, 1/16 in steps1/4 to 3/4 (6.4 to 19.1), 9 holesWiring, grommet and access holes in thin sheet
Hole saw on 1/2-20 arbor9/16 to 1-3/16 (14 to 30)Tube and grommet holes
Hole saw on 5/8-18 arbor1-1/4 (31.8) and upLightening and access holes
Hole punch, punch and die with draw screwEach punch marked with its sizeClean round holes without chips, also on the aircraft
Fly cutterAdjustableLightening holes; drill press only

What to check when buying

CheckWhat to look for
Steps1/32 or 1/16 in increments, each step marked with its size
ShankThree flats so it cannot slip in the chuck; 1/4 in on the 1/8 to 1/2 in bit, larger on bigger bits
MaterialHigh-speed steel for aluminum; cobalt for stainless steel and titanium
Hole saw teethBi-metal teeth, a pilot drill you can replace and an arbor thread that matches the saw
Punch capacitySheet thickness and alloy marked on the set; punch, die and draw screw as a matched set
Fly cutterBalanced body and a lockable arm; for a drill press only

Accessories

ItemWhat it is for
Arbor with pilot drillHolds the hole saw; 1/2-20 or 5/8-18 thread
Spare pilot drillsA dull pilot walks and spoils the start
Cutting fluidCooler cut and longer teeth in aluminum and steel
Wood backing blockSupports thin sheet so it does not tear
Half-round file and deburring toolSmooth edge on every large hole
Flanging diesFlange lightening holes to restore stiffness

Care

Keep the steps sharp and cool. A blue step is overheated and dull; slow down and use fluid.

Blow the chips out of a hole saw and push the slug out through the slots after each hole. Store bits and saws apart so the edges do not touch.

Keep each punch with its own die and screw, oil the screw thread lightly, and check the cutting edge for chips.

Safety

Clamp the sheet. A large tool grabs and spins loose sheet.

Wear eye protection; chips and slugs fly. Keep hands away from a turning hole saw and never hold the slug while the drill runs.

Questions people actually ask

Can I drill a rivet hole with a step drill?

No. Rivet and bolt holes are drilled with the twist drill sized for the fastener, so the hole is straight, round and to size. A step drill is for larger holes in thin sheet.

Step drill or hole saw?

Up to 3/4 in in thin sheet, a step drill: one tool, many sizes. Above that, a hole saw on the right arbor, or a punch for a clean hole without chips.

How are lightening holes made?

With a hole saw, a punch or a fly cutter, the edge filed smooth, then flanged. Only where the drawing or the approved repair data shows them.

Which arbor does my hole saw need?

Saws 9/16 to 1-3/16 in take the 1/2-20 arbor, 1-1/4 in and up take the 5/8-18 arbor.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close