Rivet pilot and final drills (FAA-H-8083-31, Figure 4-90)
Where to buyThe Handbook's figure lists a pilot and a final drill for each common rivet diameter. The pilot is the fractional drill of the rivet's own size; the final is the clearance drill. Clearance is the final drill minus the rivet's shank diameter.
| Rivet | Rivet Ø | Pilot drill | Final drill | Final mm | Clearance |
|---|---|---|---|---|---|
| 3/32" | 0.0938" | 3/32" (0.0937) | #40 (0.0980") | 2.49 | +0.0042" |
| 1/8" | 0.1250" | 1/8" (0.125) | #30 (0.1285") | 3.26 | +0.0035" |
| 5/32" | 0.1563" | 5/32" (0.1562) | #21 (0.1590") | 4.04 | +0.0027" |
| 3/16" | 0.1875" | 3/16" (0.1875) | #11 (0.1910") | 4.85 | +0.0035" |
| 1/4" | 0.2500" | 1/4" (0.250) | F (0.2570") | 6.53 | +0.0070" |
Pilot and final drills as printed in Figure 4-90. Clearance and the mm column are arithmetic (inches × 25.4, shank decimals rounded to four places). The Handbook text says rivet hole drills should be “the smallest size that permits easy insertion of the rivet, approximately 0.003-inch greater than the largest tolerance of the shank diameter.”
Metric alternatives, solid rivets
For solid rivets: nearest metric alternative, commonly used where inch drills cannot be bought. NOT the official drill. A metric drill is not the drill the rivet hole was designed around. The inch drill is the official one; this table is for where it cannot be bought.
| Official drill | Used for | Inches (official) | Exact mm | Nearest metric alternative, mm | Difference, mm |
|---|---|---|---|---|---|
| 3/32 in | Work, 3/32 rivet | 0.09375 in | 2.381 | 2.40 | +0.019 |
| #40 | Final, 3/32 rivet | 0.0980 in | 2.489 | 2.50 | +0.011 |
| 1/8 in | Work, 1/8 rivet | 0.1250 in | 3.175 | 3.15 or 3.20 | −0.025 or +0.025 |
| #30 | Final, 1/8 rivet | 0.1285 in | 3.264 | 3.25 | −0.014 |
| 5/32 in | Work, 5/32 rivet | 0.15625 in | 3.969 | 3.95 | −0.019 |
| #21 | Final, 5/32 rivet | 0.1590 in | 4.039 | 4.05 | +0.011 |
| 3/16 in | Work, 3/16 rivet | 0.1875 in | 4.763 | 4.75 | −0.013 |
| #11 | Final, 3/16 rivet | 0.1910 in | 4.851 | 4.85 | −0.001 |
| 1/4 in | Work, 1/4 rivet | 0.2500 in | 6.350 | 6.35 | 0.000 |
| F | Final, 1/4 rivet | 0.2570 in | 6.528 | 6.55 | +0.022 |
Exact mm = inches × 25.4. The alternative is the nearest size on a 0.05 mm step; the difference is that size minus the exact size. 1/8 in falls exactly halfway, so both neighbors are shown: neither equals 1/8 in. For a #30 solid-rivet hole, 3.25 mm is −0.014 mm and 3.30 mm is +0.036 mm. This table is for solid rivets; for CherryMAX and CherryLOCK the maker's hole range decides (see Metric alternatives for blind rivets). This table approves no hole: the tolerance is set by the manual (SRM, AMM or drawing).
Metric alternatives for blind rivets
For CherryMAX and CherryLOCK the metric drill is chosen inside the maker's hole range, not by nearest size. Cherry gives a minimum and a maximum hole; a metric drill whose size falls outside it is not offered here. Not the official drill.
| Official drill | Used for | Maker's hole range, in | Metric inside the range, mm | = inches | Nearest metric, mm |
|---|---|---|---|---|---|
| #40 | CherryLOCK 3/32 in | 0.097 to 0.100 | 2.50 | 0.0984 | 2.50 (inside) |
| #30 | CherryMAX / CherryLOCK -4 (1/8 in) | 0.129 to 0.132 | 3.30 | 0.1299 | 3.25 (outside) |
| #20 | -5 (5/32 in) | 0.160 to 0.164 | 4.10 | 0.1614 | 4.10 (inside) |
| #10 | -6 (3/16 in) | 0.192 to 0.196 | 4.90 | 0.1929 | 4.90 (inside) |
| F | -8 (1/4 in) | 0.256 to 0.261 | 6.55 | 0.2579 | 6.55 (inside) |
| #27 | -4 oversize / bulbed | 0.143 to 0.146 | 3.65 | 0.1437 | 3.65 (inside) |
| #16 | -5 oversize / bulbed | 0.176 to 0.180 | 4.50 | 0.1772 | 4.50 (inside) |
| #5 | -6 oversize / bulbed | 0.205 to 0.209 | 5.25 | 0.2067 | 5.20 (outside) |
| I | -8 oversize | 0.271 to 0.275 | 6.90 | 0.2717 | 6.90 (inside) |
Limits: The Aviation Point data. Metric sizes are on a 0.05 mm step, chosen as the nearest to the official drill that lies inside the maker's range; mm and inches are conversions. For solid rivets use the table above (nearest size). A go/no-go gage decides the hole. The calculator drill for part number gives the same figures. This table approves no hole: the SRM or drawing comes first.
Number drills, #1 to #40
A bigger number is a smaller drill. #1 is 0.2280 in and #80 is 0.0135 in. The four you will use most on rivets are in bold in the rivet table above: #40, #30, #21 and #11.
| Drill | Decimal (in) | mm |
|---|---|---|
| #1 | 0.2280" | 5.79 |
| #2 | 0.2210" | 5.61 |
| #3 | 0.2130" | 5.41 |
| #4 | 0.2090" | 5.31 |
| #5 | 0.2055" | 5.22 |
| #6 | 0.2040" | 5.18 |
| #7 | 0.2010" | 5.11 |
| #8 | 0.1990" | 5.05 |
| #9 | 0.1960" | 4.98 |
| #10 | 0.1935" | 4.91 |
| #11 | 0.1910" | 4.85 |
| #12 | 0.1890" | 4.80 |
| #13 | 0.1850" | 4.70 |
| #14 | 0.1820" | 4.62 |
| Drill | Decimal (in) | mm |
|---|---|---|
| #15 | 0.1800" | 4.57 |
| #16 | 0.1770" | 4.50 |
| #17 | 0.1730" | 4.39 |
| #18 | 0.1695" | 4.31 |
| #19 | 0.1660" | 4.22 |
| #20 | 0.1610" | 4.09 |
| #21 | 0.1590" | 4.04 |
| #22 | 0.1570" | 3.99 |
| #23 | 0.1540" | 3.91 |
| #24 | 0.1520" | 3.86 |
| #25 | 0.1495" | 3.80 |
| #26 | 0.1470" | 3.73 |
| #27 | 0.1440" | 3.66 |
| #28 | 0.1405" | 3.57 |
| Drill | Decimal (in) | mm |
|---|---|---|
| #29 | 0.1360" | 3.45 |
| #30 | 0.1285" | 3.26 |
| #31 | 0.1200" | 3.05 |
| #32 | 0.1160" | 2.95 |
| #33 | 0.1130" | 2.87 |
| #34 | 0.1110" | 2.82 |
| #35 | 0.1100" | 2.79 |
| #36 | 0.1065" | 2.71 |
| #37 | 0.1040" | 2.64 |
| #38 | 0.1015" | 2.58 |
| #39 | 0.0995" | 2.53 |
| #40 | 0.0980" | 2.49 |
Number drills, #41 to #80
A bigger number is a smaller drill. #1 is 0.2280 in and #80 is 0.0135 in. The four you will use most on rivets are in bold in the rivet table above: #40, #30, #21 and #11.
| Drill | Decimal (in) | mm |
|---|---|---|
| #41 | 0.0960" | 2.44 |
| #42 | 0.0935" | 2.37 |
| #43 | 0.0890" | 2.26 |
| #44 | 0.0860" | 2.18 |
| #45 | 0.0820" | 2.08 |
| #46 | 0.0810" | 2.06 |
| #47 | 0.0785" | 1.99 |
| #48 | 0.0760" | 1.93 |
| #49 | 0.0730" | 1.85 |
| #50 | 0.0700" | 1.78 |
| #51 | 0.0670" | 1.70 |
| #52 | 0.0635" | 1.61 |
| #53 | 0.0595" | 1.51 |
| #54 | 0.0550" | 1.40 |
| Drill | Decimal (in) | mm |
|---|---|---|
| #55 | 0.0520" | 1.32 |
| #56 | 0.0465" | 1.18 |
| #57 | 0.0430" | 1.09 |
| #58 | 0.0420" | 1.07 |
| #59 | 0.0410" | 1.04 |
| #60 | 0.0400" | 1.02 |
| #61 | 0.0390" | 0.99 |
| #62 | 0.0380" | 0.97 |
| #63 | 0.0370" | 0.94 |
| #64 | 0.0360" | 0.91 |
| #65 | 0.0350" | 0.89 |
| #66 | 0.0330" | 0.84 |
| #67 | 0.0320" | 0.81 |
| #68 | 0.0310" | 0.79 |
| Drill | Decimal (in) | mm |
|---|---|---|
| #69 | 0.0293" | 0.74 |
| #70 | 0.0280" | 0.71 |
| #71 | 0.0260" | 0.66 |
| #72 | 0.0250" | 0.64 |
| #73 | 0.0240" | 0.61 |
| #74 | 0.0225" | 0.57 |
| #75 | 0.0210" | 0.53 |
| #76 | 0.0200" | 0.51 |
| #77 | 0.0180" | 0.46 |
| #78 | 0.0160" | 0.41 |
| #79 | 0.0145" | 0.37 |
| #80 | 0.0135" | 0.34 |
Decimals as printed in Figure 4-47; millimeters are the inch value × 25.4.
Letter drills, A to Z
Letter drills start where number drills end: A (0.2340 in) is larger than #1 (0.2280 in). Z is 0.4130 in.
| Drill | Decimal (in) | mm |
|---|---|---|
| A | 0.2340" | 5.94 |
| B | 0.2380" | 6.05 |
| C | 0.2420" | 6.15 |
| D | 0.2460" | 6.25 |
| E | 0.2500" | 6.35 |
| F | 0.2570" | 6.53 |
| G | 0.2610" | 6.63 |
| H | 0.2660" | 6.76 |
| I | 0.2720" | 6.91 |
| J | 0.2770" | 7.04 |
| K | 0.2810" | 7.14 |
| L | 0.2900" | 7.37 |
| M | 0.2950" | 7.49 |
| Drill | Decimal (in) | mm |
|---|---|---|
| N | 0.3020" | 7.67 |
| O | 0.3160" | 8.03 |
| P | 0.3230" | 8.20 |
| Q | 0.3320" | 8.43 |
| R | 0.3390" | 8.61 |
| S | 0.3480" | 8.84 |
| T | 0.3580" | 9.09 |
| U | 0.3680" | 9.35 |
| V | 0.3770" | 9.58 |
| W | 0.3860" | 9.80 |
| X | 0.3970" | 10.08 |
| Y | 0.4040" | 10.26 |
| Z | 0.4130" | 10.49 |
Decimals as printed in Figure 4-47. E and 1/4 in are both 0.2500 in.
Fractional drills, 1/64 to 1/2 in by 64ths
| Drill | Decimal (in) | mm |
|---|---|---|
| 1/64" | 0.0156" | 0.40 |
| 1/32" | 0.0312" | 0.79 |
| 3/64" | 0.0468" | 1.19 |
| 1/16" | 0.0625" | 1.59 |
| 5/64" | 0.0781" | 1.98 |
| 3/32" | 0.0937" | 2.38 |
| 7/64" | 0.1093" | 2.78 |
| 1/8" | 0.1250" | 3.18 |
| 9/64" | 0.1406" | 3.57 |
| 5/32" | 0.1562" | 3.97 |
| 11/64" | 0.1718" | 4.36 |
| 3/16" | 0.1875" | 4.76 |
| 13/64" | 0.2031" | 5.16 |
| 7/32" | 0.2187" | 5.55 |
| 15/64" | 0.2343" | 5.95 |
| 1/4" | 0.2500" | 6.35 |
| Drill | Decimal (in) | mm |
|---|---|---|
| 17/64" | 0.2656" | 6.75 |
| 9/32" | 0.2812" | 7.14 |
| 19/64" | 0.2968" | 7.54 |
| 5/16" | 0.3125" | 7.94 |
| 21/64" | 0.3281" | 8.33 |
| 11/32" | 0.3437" | 8.73 |
| 23/64" | 0.3593" | 9.13 |
| 3/8" | 0.3750" | 9.53 |
| 25/64" | 0.3906" | 9.92 |
| 13/32" | 0.4062" | 10.32 |
| 27/64" | 0.4219" | 10.72 |
| 7/16" | 0.4375" | 11.11 |
| 29/64" | 0.4531" | 11.51 |
| 15/32" | 0.4687" | 11.90 |
| 31/64" | 0.4844" | 12.30 |
| 1/2" | 0.5000" | 12.70 |
Decimals as printed in Figure 4-47, which truncates some of them rather than rounding (3/32 is exactly 0.09375 but is printed 0.0937). The Handbook prints 1/64 as “1/54” and 39/64 as “39/84”; the typos are corrected here. The Handbook chart continues to 1 in.
Which series, and in what order
Drills come in three series that interleave: number (#80 up to #1), letter (A up to Z) and fractional (1/64 in steps). Sheet metal work lives mostly in the number series, because rivet holes are small and need small steps. The Handbook says drill diameters “are grouped by three size standards: number, letter, and fractional.”
A fractional drill is rarely the right drill for a rivet. A 1/8 in drill is exactly 0.1250 in, the same as a 1/8 in rivet shank, so the rivet has no clearance. That is why Figure 4-90 uses the fractional size only as the pilot and a number drill as the final.
Pilot drills and holes above 3/16 in
The Handbook describes the procedure for holes larger than 3/16 in in sheet metal as: “drill a pilot hole with a No. 40 or No. 30 drill bit and then to oversize with a larger drill bit to the correct size.” (Chapter 4, step drill bits, p. 4-17.) On rivet holes it also says to drill “a slightly undersized hole (pilot hole)” and ream it with the proper twist drill (p. 4-40).
Where the sources differ: Figure 4-90 shows the fractional drill as the pilot for each rivet size, while the text names a No. 40 or No. 30 as the pilot for larger holes. The common shop habit of #41 before #40 or #31 before #30 is in neither source; see the rivet drill chart.
Worked example — 5/32 in rivet
A 5/32 in rivet line in sheet metal. Look the sizes up in the rivet table and the number table.
- Pilot: 5/32 in (0.1562 in as printed in Figure 4-90). Final: #21 (0.1590 in).
- Clearance: 0.1590 − 0.1563 = 0.0027 in.
- In millimeters: 0.1590 × 25.4 = 4.04 mm.
- Deburr both sides after drilling, as the Handbook says, before riveting.
Final drill #21, 0.1590 in, 4.04 mm. Check the drawing or SRM, which can call for a different hole.
Where the sources agree, and where they do not
| Point | First source | Second source | Where they differ, and what governs |
|---|---|---|---|
| Rivet drill, 1/8 in | Handbook p. 4-44, Fig. 4-90: #30 (0.1285 in) | MIL-R-47196A Table I: #30 | Agree. |
| Rivet drill, 5/32 in | Handbook p. 4-44, Fig. 4-90: #21 (0.1590 in) | MIL-R-47196A Table I: #20 (0.1610 in) | One number apart; the repair data's callout governs, the smaller where it gives none. |
| Decimal of each drill | ASME B94.11M: number, letter and fraction series | Handbook Fig. 4-90: the same decimals for the rivet drills | Agree. |
| Hole quality | AC 43.13-1B par. 4-58: round, straight, free of cracks | Handbook p. 4-40: burr remover or larger drill bit | Agree. |
Questions people actually ask
What drill size for a 1/8 inch rivet?
#30, 0.1285 in (3.26 mm). Figure 4-90 gives a 1/8 in pilot (0.125 in) and a #30 final.
Is a #1 drill bigger than a #60?
Yes. #1 is 0.2280 in and #60 is 0.0400 in. Number drills get smaller as the number goes up.
Is an A drill bigger than a #1?
Yes, A is 0.2340 in and #1 is 0.2280 in. Letters start where numbers stop.
What size is a #40 drill in millimeters?
0.0980 in × 25.4 = 2.49 mm.
Why is the rivet hole drill bigger than the rivet?
For clearance. Figure 4-90 gives 0.0027 in to 0.0042 in on the four smaller rivets and 0.0070 in on the 1/4 in rivet with an F drill. The rivet swells when driven and fills the hole.
Limits — when NOT to use this chart
Decimal sizes are for the drill itself. The hole a drill cuts can be larger, and the hole a drawing calls for is often not the drill size.
- The drawing or SRM governs hole size. The Handbook says hole sizes for other fasteners are found on work documents, prints or in manuals.
- Blind rivets, Hi-Lok and lockbolts have their own hole and reaming sizes. Do not take them from the rivet table.
- Bolt holes follow AC 43.13-1B par. 7-39, the first-lettered drill larger than the bolt, except in close-fit or reamed holes. Use the bolt hole calculator.
- A worn bit cuts oversize. Measure the hole, not the bit.
- Metric drills are nearest alternatives, not official drills. The mm columns convert the inch drill; the metric table names the nearest size, and the manual sets the tolerance.
Where to buy
Are you a distributor? Get listed →
Distributors coming soon.
Main sources
- FAA-H-8083-31, AMT Handbook — Airframe, Volume 1, Chapter 4, Figure 4-47 (p. 4-18) — “Drill sizes and decimal equivalents”: every decimal in the number, letter and fractional tables. The decimals are the Handbook's printed values; the two typos noted above are corrected.
- FAA-H-8083-31, Airframe, Volume 1, Chapter 4, Figure 4-90 (p. 4-40) and p. 4-17 — pilot and final drills for 3/32 to 1/4 in rivets, the 0.003 in clearance rule, the pilot-hole procedure and the No. 40 / No. 30 pilot for holes above 3/16 in.
- FAA AC 43.13-1B CHG 1, Chapter 7, par. 7-39 — bolt fit and the first-lettered drill rule referred to in the limits.
- FAA AC 43.13-1B CHG 1, Acceptable Methods, Techniques, and Practices: Aircraft Inspection and Repair — Par. 4-58: hole preparation.
- MIL-R-47196A, Rivets, Buck Type, Preparation for and Installation — Table I: drill sizes for solid rivets.
- ASME B94.11M, Twist Drills — Number, letter and fraction series and their decimal sizes.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, Chapter 4 — Figures and paragraphs named in the rows above.
Cross-checked with other manuals and standards in our library.
