Measuring Tools: Calipers, Micrometers and Dial Indicators

A dial or digital caliper reads .001 in (0.025 mm) and covers most sheet metal checks; an outside micrometer reads .001 in, or .0001 in with a vernier, for skin thickness and shank sizes. Buy tools with a calibration certificate and check zero before each use.

View PDF

What they measure

Where to buy

A caliper takes four readings with one tool: outside sizes between the lower jaws, inside sizes between the upper jaws, depth with the rod that slides out of the beam end, and steps with the end of the slider against the fixed jaw.

A micrometer measures between an anvil and a spindle driven by a fine thread. It reads finer than a caliper and is the tool for skin thickness, rivet shank and drill shank diameters.

A dial indicator on a base measures a movement, not a size: flushness of a head, runout of a drill, the height of a step against a reference surface.

Drawing

ITEMDESCRIPTION1BEAM2FIXED JAW3SLIDER4OUTSIDE JAWS5INSIDE JAWS6DIAL7THUMB ROLLER8LOCK SCREW9DEPTH ROD10BEAM SCALECALIPER, DIALSHEET 1 OF 1DWG TAP-TG-055REV ASCALE 1:1.47READINGSREADSWITHOUTSIDEITEM 4INSIDEITEM 5DEPTHITEM 9STEPITEM 3NOTES1.CLOSE THE JAWSAND ZERO THE DIALBEFORE EACH USE.2.MEASURE WITHLIGHT, EVENPRESSURE ON THEROLLER.3.MEASURE NEAR THEBEAM, NOT AT THEJAW TIPS. TAPADVICE.4.CHECK AGAINST AGAUGE BLOCK OFKNOWN SIZE.FRONT VIEWSCALE 0.68:1AASECTION A-ASCALE 2:112345678910
Dial caliper with the jaws closed: the outside, inside, depth and step readings, and section A-A through the slider and the beam.

Types

TypeSize or range, inches (mm)Where it fits
Dial caliper6, 8 or 12 (150, 200 or 300); reads .001 (0.025)Outside, inside, depth and step readings on the bench and at the aircraft
Digital caliper6, 8 or 12 (150, 200 or 300); shows .0005 (0.01)The same readings with inch and mm at the press of a button
Vernier caliper6 to 12 (150 to 300); reads .001 (0.02 on metric scales)No battery, no gear train: the reference caliper of the shop
Outside micrometer0 to 1 (0 to 25); reads .001, .0001 with a vernierSkin thickness, rivet shank, drill shank and pin diameters
Depth micrometerRods in 1 (25) steps; reads .001Depth of steps, recesses and counterbores
Dial indicatorReads .001 or .0001 per divisionFlushness, runout and step height from a base or a stand
Steel rule6 and 12 (150 and 300); 1/64 and 1/100 graduationsLayout, edge distance and rivet pitch on the sheet

What to check when buying

CheckWhat to look for
Resolution.001 in (0.025 mm) for a caliper; .0001 in for a micrometer used on skins and shanks
Calibration certificateTraceable to a national standard, with the serial number of the tool
Measuring facesHardened or carbide faces, flat and parallel, no nicks
Micrometer stopRatchet or friction thimble, so every reading has the same force
ZeroThe dial or display returns to zero with the jaws closed, every time
LockLock screw on the slider and lock ring on the micrometer spindle
Digital caliperInch and mm, a standard battery and a display that holds a reading
CaseA fitted case that keeps the jaws and faces apart from other tools

Accessories

ItemWhat it is for
Gauge blocksKnown sizes to check a caliper or a micrometer before use
Micrometer standardThe setting rod for a micrometer whose range does not start at zero
Magnetic baseHolds a dial indicator on a steel table or a fixture
Indicator pointsFlat, ball and long points for flushness and step readings
Spare batteryFor digital calipers and indicators
Lint-free clothCleans the faces before each reading

Care

Clean the faces before each reading and close the jaws to check zero. Never use a caliper as a scribe, a wrench or a depth stop.

Store the tool open, with the faces apart and the lock loose, in its case. Keep a calibrated tool away from drops; after a drop, check it against a gauge block before the next reading.

Keep chips out of the dial gear and the beam rack: blow them off with low pressure air away from the dial and wipe the beam.

Safety

Caliper jaw tips are sharp. Close the jaws and lock them before the tool goes back into a pocket or a case.

Never measure a turning part. Stop the drill or the machine before a caliper or a micrometer goes near it.

Questions people actually ask

Caliper or micrometer for skin thickness?

A micrometer: it reads finer, and its flat anvil and spindle measure a skin without the spring of caliper jaws. A caliper is fine for a quick check to .001 in.

Dial or digital caliper?

Both read .001 in. The dial needs no battery and shows a trend as the jaws move; the digital switches between inch and mm and holds a reading. Many shops keep one of each.

How do I read a micrometer?

Add the last number shown on the sleeve (each is .100 in), the sleeve lines past it (each .025 in) and the thimble line on the reference line (each .001 in). With a vernier, add the vernier line that matches (each .0001 in).

How often must a measuring tool be calibrated?

At the interval of the shop quality system, and after any drop or doubtful reading. The due date goes on the tool.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close