Clamps and Vises: Side-Grip, C-Clamps, Locking Pliers and Soft Jaws

Clamps hold parts where a temporary fastener cannot go: before the holes are drilled, at an edge or a flange, and at the bench. Pad every jaw that touches the part and tighten by hand only, so the clamp holds without marking the skin.

View PDF

What it is

Where to buy

A clamp presses parts together between two jaws. A C-clamp has a frame shaped like a C, a screw threaded through one end of the frame and a swivel pad on the end of the screw, so the screw turns without turning against the work. A bench vise has a fixed jaw on the body, a movable jaw driven by the screw and handle, and a swivel base bolted to the bench.

In sheet-metal work, clamps hold a doubler or a skin in place before the first holes are drilled, hold an edge or a flange where a temporary fastener cannot go, and hold parts at the bench for filing, drilling and forming. Use a C-clamp for work that cannot be held in a vise or must be held for a long time. Steel jaws mark aluminum: put soft caps on the vise jaws and protective blocks or shims under every clamp pad.

Drawing

ITEMDESCRIPTION1FRAME2SCREW3HANDLE, SLIDING4PAD, SWIVEL5BLOCK, PROTECTIVE6WORK (REF)7BODY, FIXED JAW8JAW, MOVABLE9CAP, SOFT JAW10HANDLE, VISE11BASE, SWIVELCLAMP, C, AND VISE, BENCH, SOFT JAWSSHEET 1 OF 1DWG TAP-TG-094REV ASCALE 1:1TOOL FOR THE WORKWORKTOOLEDGE, FLANGESIDE-GRIP CLAMPLAP, LONG HOLDC-CLAMPBENCH WORKVISE, SOFT CAPSQUICK HOLDLOCKING PLIERSJAW PROTECTIONSURFACEPADSOFT METALBRASS, COPPER CAPPOLISHEDLEATHER, RAWHIDEPAINTED, CLADPAD OR BLOCKNOTES1.TIGHTEN BY HAND ONLY: NO WRENCHOR BAR.2.C-CLAMP OPENING 1 1/2 TO 2 IN (38TO 51 MM) WIDER THAN THE WORK.3.EVEN PRESSURE OVER THE WHOLE PAD.4.NEVER OIL THE SWIVEL BASE.THROATWORKBC-CLAMP, ELEVATIONSCALE 1:2DETAIL B, SECTIONSCALE 2:1CBENCH VISE, ELEVATIONSCALE 1:3DETAIL C, SECTIONSCALE 1:11234567891011
C-clamp in elevation at 1:2 holding the work between protective blocks; detail at 2:1 of the swivel pad on the ball end of the screw; bench vise in elevation at 1:3; detail at 1:1 of the soft jaw caps on the work (items 1 to 11). Tool and jaw protection tables.

Types and sizes

TypeSizeUse
Side-grip clampBy grip rangeHolds an edge or a flange from the side, with no hole; fitted with the same pliers as temporary sheet fasteners.
C-clampBy opening and throat depthLaps, doublers and work that cannot go in a vise or must be held for a long time.
Locking pliers, C-clamp jawsBy length and jaw openingA quick hold at an edge; swivel pads spread the load.
Locking pliers, wide flat jawsBy jaw widthHolding and bending a narrow flange or a short edge.
Bench viseBy jaw width and openingParts at the bench: filing, drilling, forming; always with soft jaw caps.
Soft jaw capsBy jaw widthBrass, copper or other soft caps over the vise jaws.
Hand screw clampBy jaw lengthTwo wood or plastic jaws and two screws; blocks and forming dies.

What to check when buying

CheckWhat to look for
OpeningC-clamp opening 1 1/2 to 2 in (38 to 51 mm) wider than the work you hold most.
Throat depthDeep enough to reach past the flange or the edge to where the pad must sit.
PadsSwivel pads that tilt freely and take soft covers; non-marring pads on locking pliers.
ScrewRuns smooth over the full opening with no play at the swivel pad.
FrameNo cracks or bending; the frame must not spring when the screw is tight.
ViseJaw width and opening for your parts, a swivel base that locks, jaws that take soft caps.
Side-grip clampsGrip range marked, a spring that holds, jaws that close parallel.

Accessories

ItemWhat it is for
Soft jaw capsBrass or copper caps over vise jaws for soft metals.
Leather or rawhide padsHighly polished surfaces.
Wood blocks and brass shimsBetween the clamp pads and the work, to spread the load.
Pad coversPlastic covers for the swivel pads of C-clamps and locking pliers.
Temporary fastener pliersFit side-grip clamps.

Care

Vise. Clean it with a rag after use and give it a light coat of oil. Never oil the swivel base or the swivel joint: oil there reduces the holding power. Store it with the jaws lightly closed and the handle vertical.

Clamps. Keep the screws clean and lightly oiled and the swivel pads free. Replace worn pad covers and soft caps.

Locking pliers. Keep the jaws clean and the adjusting screw free; replace pliers whose jaws no longer close parallel.

Safety

Hand tight. Tighten clamps by hand only: never with a wrench or a bar. Too much force springs the frame and marks the work.

Even pressure. Check that the clamp presses evenly over the whole pad before you drill.

Pinch points. Keep fingers out of the jaws and the release lever of locking pliers.

Bench. Bolt the vise to a solid bench and keep the handle clear of the walkway.

Questions people actually ask

Clamp or temporary fastener?

Temporary fasteners go in drilled holes and pull the sheets together hole by hole. Clamps hold before there are holes, at an edge, a flange, or at the bench. See temporary fasteners.

What size of C-clamp do I need?

One whose opening is 1 1/2 to 2 in (38 to 51 mm) wider than the work, with the protective blocks counted in the work, and a throat deep enough to reach the place of the pad.

Why put a block between the clamp and the sheet?

The block spreads the pad load and keeps the pad off the skin, so the clamp leaves no mark on clad or painted sheet.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close