Fastener Cross-Reference Chart

AN960 became NAS1149, AN470 became MS20470, and MS20426 became NASM20426. This chart lists the crosses that standards and notices document, with the status of each and a link to the decoder. MS20470 is not NAS1097: one is a universal head, the other a reduced countersunk head.

View PDF
CalculatorPart Number Equivalent Cross-Reference & DecoderFind the equivalent of any aircraft part numberOpen the calculator →
Not every look-alike is a cross. MS20470 is not NAS1097. MS20470 is a universal-head rivet; NAS1097 is a 100° countersunk rivet with a reduced head. They do not replace each other. A cross appears here only where a standard's own notice, interchangeability table or listing states it.

How to read the status

Where to buy

Superseded means the standard on the left was replaced by the one on the right, and new stock is ordered under the right-hand number. Adopted as NASM means the Air Force-Navy MS standard was canceled and re-issued as a NASM standard of the same number; the notices say what changed, if anything.

The right-hand column does not say the parts are interchangeable on your aircraft. Where the drawing, IPC or SRM names a part number, that number governs. The decoder takes the old number you hold and shows the current one, the size, and the data sheet.

Solid rivets

Old numberCurrent numberStatusTry in the decoderSource
AN470MS20470SupersededAN470AD4-6MS20470H note 2 (p. 2); AC 43.13-1B 4-57a(4), 7-1a
AN426MS20426SupersededAN426AD4-6MS20426L note 2 (p. 2); AC 43.13-1B 4-57a(4), 7-1e
MS20426NASM20426Canceled, adopted as NASM; part numbers identicalMS20426AD4-6MS20426L Notice 1 (18 Aug 1998)
AN435 (carbon steel, CRES)MS20613SupersededMS20613-4C5AC 43.13-1B Table 4-8
AN435 (Monel, brass)MS20615SupersededMS20615-4M5AC 43.13-1B Table 4-8
AN427MS20427SupersededMS20427M4-5MS20427H notes 3 and 4: like dash numbers interchangeable
MS20613NASM20613SupersededMS20613-4C5MS20613F standard sheet
MS20615NASM20615SupersededMS20615-4M5MS20615G standard sheet
MS20427NASM20427SupersededMS20427M4-5MS20427H (adoption notice 19 Apr 1999)
MS14218NASM14218SupersededMS14218E4-4NASM14218 listing (2014 revision)
BRFZ (BRFZ4E4)MS14218Same item (NSN)BRFZ4E4NSN record (Federal Catalog System): 27 of 28 pairs, diameter written before the material
BACR15FV, VRFZMS14218Same item (NSN)BACR15FV6E16NSN record (Federal Catalog System): same NSN, number by number
BACR15CENAS1097Same item (NSN)NAS1097KE4-4NSN record (Federal Catalog System): 6 of 6 pairs
MS20426 E (7050)NASM20426 ECanceled, adopted as NASM; part numbers identicalMS20426E4-5MS20426L (E = 7050-T73) and Notice 1 (18 Aug 1998)
BRFZ E (7050)MS14218 ESame item (NSN)BRFZ5E3NSN record (Federal Catalog System): BRFZ5E3 and MS14218E5-3 share one NSN
NAS1097 KENAS1097 ESame alloy, two letters: KE is the NAS letter for 7050NAS1097KE4-4MIL-HDBK-5J Table 8.1.2(b) note h; FAA-H-8083-31B Fig. 4-77
AN427 (Monel)MS20427 M (Monel)SupersededMS20427M4-5MS20427H notes 3 and 4; AC 43.13-1B Table 4-8
AN427 (CRES)MS20427 F (CRES)SupersededMS20427F2-2MS20427H notes 3 and 4; AC 43.13-1B Table 4-8
CRES letter F (AN tables)MS20613 C (CRES)Same alloy, different letterMS20613-4C5AC 43.13-1B Table 4-8; MS20613F

Same item (NSN): both numbers share one NSN in the public federal data, true for that exact item; the decoder shows each one.

Oversize Hi-Lok and Jo-Bolt fasteners

Standard fastenerOversizeStatusTry in the decoderSource
HL18HL62 (1/64 in), HL218 (1/32 in)Oversize, not an equivalentHL62PB6-2Hi-Shear/LISI HL62 rev. 18, HL218 rev. 11
HL19HL63 (1/64 in), HL219 (1/32 in)Oversize, not an equivalentHL63PB6-2Hi-Shear/LISI drawings
HL10, HL11HL110, HL111 (1/64 in)Oversize, not an equivalentHL110VAZ6Hi-Shear/LISI drawings
NAS1669, NAS1670 (Jo-Bolt)Oversize type, no public number or hole figureExists, no public data—TM 1-1500-204-23-6 para. 2-2p(4)

An oversize pin keeps the first dash of the pin it replaces, goes in the hole opened up to it and needs its own collar. Hole preparation per NAS618, which gives the band for each fit class; the drawing or the SRM picks the class. The SRM, the drawing or the approved repair data governs.

Washers

Old numberCurrent numberStatusTry in the decoderSource
AN960NAS1149Canceled; the notice has a substitution tableAN960-416AN960 Rev. 21 Notice 1 (16 Sep 2011)
AN970NASM970Canceled; identical itemAN970AN970 Rev. 6 Notice 4 (28 Jul 1999)
AN935MS35338SupersededAN935-10AN935 standard sheets (washer)
MS35338NASM35338Superseded by NASMMS35338-44MS35337 thru MS35340 standard sheets (washer)
MS15795NASM15795Superseded by NASMMS15795-603MS15795 standard sheets (washer)

Nuts, cotter pins and clevis pins

Old numberCurrent numberStatusTry in the decoderSource
AN365MS20365SupersededAN365-1032MS21042 thru MS21046 standard sheets (nut)
MS20365MS21042SupersededMS20365-440MS20364 and MS20365 standard sheets (nut)
MS20364MS21083SupersededMS21083N06MS20364 and MS20365 standard sheets (nut)
MS21042NASM21042Superseded by NASMMS21042L08MS21042 thru MS21046 standard sheets (nut)
AN380MS24665SupersededAN380-2-2AN380 Rev. 7 Notice 1 (1 Aug 1968)
MS24665NASM24665Superseded by NASMMS24665-283MS24665F Notice 2 (30 Nov 1998)
AN392MS20392SupersededAN392-11AN392 thru AN406 standard sheets (pin)
AN995NASM20995Superseded (adoption notice)MS20995C32NASM20995 adoption notice (30 Apr 1998)

Screws

Old numberCurrent numberStatusTry in the decoderSource
AN505MS35190SupersededAN505-10-10AN505 Rev. 7, sheet 4
AN510MS35191SupersededAN510-0-2MS35191G, Table II
AN515MS35206SupersededAN515-10-10MS35206H, Table III
AN520MS51958SupersededAN520C10-10MS51958C, interchangeability table
AN507MS24693SupersededAN507-1032R10AN507 standard sheets (screw)
AN509MS24694SupersededAN509-10R10MS24694C, Table IV
AN530MS51861SupersededAN530C10-10MS51861A, Table III

Worked example

The kit list says AN960-416 and the stockroom only has NAS1149 washers.

  1. Find AN960 in the washers table: canceled, replaced by NAS1149.
  2. Type AN960-416 in the decoder: it gives the NAS1149 number for that size and finish, from the notice's substitution table.
  3. Check the drawing or IPC allows the NAS part, then order from the catalog.

Order the NAS1149 number the decoder shows, after the drawing check.

Where the sources agree, and where they do not

PointFirst sourceSecond sourceWhere they differ, and what governs
Part numberAC 43.13-1B Fig. 4-4: MS20470AD4-7, diameter in 32nds (4 = 1/8 in), length in 16ths (7 = 7/16 in)Chart: the dash numbers of each standardAgree. Half sizes carry 0.5 after the length (MS20470AD4-3.5).
Replacing alloysAC 43.13-1B par. 4-57: 2017 rivets of 3/16 in or less and 2024 rivets of 5/32 in or less may be replaced by 2117 rivets 1/32 in largerChart rows above: equivalents compared by standard, diameter and materialThe AC allows a change of alloy only with the larger diameter; the repair data may not allow it.
Blind rivetsAC 43.13-1B par. 4-57: not in fluid-tight areas, air intake areas, control surfaces, hinges, landing gear fittings or heavily stressed placesChart: blind equivalents listed with their standardThe AC restriction applies to every blind row; metal airframe repairs with them need the maker's or FAA authorization.

Questions people actually ask

Is MS20470 the same as NAS1097?

No. MS20470 has a universal head and NAS1097 a 100° reduced countersunk head. A countersunk MS rivet is MS20426, and NAS1097 is a separate standard (AC 43.13-1B Table 7-10).

Does "superseded" mean I can swap without checking?

No. The notice says what replaced what. Whether your aircraft accepts it depends on its drawing, IPC or SRM.

Why are distributor equivalents missing?

Only standards, notices and listings are used here. Distributor and NSN equivalents are in the data sheets, labeled by level.

Limits — when NOT to use this chart

What the sources support, and no further.

  • Common crosses only. Other series are in the data sheets; the AN3 to NASM3 bolt series is not covered here.
  • Status as of the notice or listing cited. A later revision may change it. Check the current issue.
  • The SRM and IPC govern where they name a part number.

Where to buy

AmericaDistributor coming soon
EuropeDistributor coming soon
OceaniaDistributor coming soon

Are you a distributor? Get listed →

Distributors coming soon.

Main sources

  • FAA AC 43.13-1B CHG 1, Chapter 4 par. 4-57 and Chapter 7 par. 7-1 — AN470 and AN426 superseded by MS20470 and MS20426; NAS1097 in Table 7-10.
  • MS20470H and MS20426L with Notice 1; AN960 Rev. 21 Notice 1; AN970 Rev. 6 Notice 4; MS24665F Notice 2; NASM20995 adoption notice — Cancellation and adoption notices (public documents).
  • Screw standards MS35190, MS35191G, MS35206H, MS51958C, MS24694C, MS51861A and AN505 Rev. 7 — Interchangeability tables and supersession notes, per row above.
  • FAA AC 43.13-1B CHG 1, Acceptable Methods, Techniques, and Practices: Aircraft Inspection and Repair — Fig. 4-4 and par. 4-57: part numbers, replacement, blind rivets.

Cross-checked with other manuals and standards in our library.

Educational reference only. Not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.
esc
↑↓ navigate↵ openesc close