Specification
Where to buy| Item | Value |
|---|---|
| Type | Offset pulling head |
| Maker | Cherry Aerospace |
| Tool sheet | TS-H563B, Rev. D, 10/12/17 |
Part numbers
Cherry's part numbers on this tool sheet.
1/8 in (-4)2 part numbers
| Part no. |
|---|
| H563-4B |
| H563SP-4B |
5/32 in (-5)2 part numbers
| Part no. |
|---|
| H563-5B |
| H563SP-5B |
3/16 in (-6)2 part numbers
| Part no. |
|---|
| H563-6B |
| H563SP-6B |
What it installs as supplied
| Fastener | Diameter | Note |
|---|---|---|
| Lockbolt (3/8 nose projection; short pintail lockbolts using letter 'Y' for SP versions) | 4, 5, 6 | Assemblies H563-4B/-5B/-6B and H563SP-4B/-5B/-6B |
Riveters
Parts by head size
| Fastener | Dia. | Parts | Jaws | Note |
|---|---|---|---|---|
| Lockbolt 3/8 nose projection | 4 | (sleeve -1) 563B2 / anvil -11 562A6-4 / ejector sleeve -12 563A9-4 | -13: P-609 | H563-4B; snubber -15: 563B25-4 |
| Lockbolt 3/8 nose projection | 5 | (sleeve -1) 563B2 / anvil -11 562A6-5 / ejector sleeve -12 563A9-5 | -13: 513-077 | H563-5B; snubber -15: 563B25-5 |
| Lockbolt 3/8 nose projection | 6 | (sleeve -1) 563B2 / anvil -11 562A6-6 / ejector sleeve -12 563A9-6 | -13: 563-031 | H563-6B; snubber -15: 563B25-6 |
| Short pintail lockbolts using letter 'Y' | 4 | (sleeve -1) 563B12 / anvil -11 563A14-4 / ejector sleeve -12 563A13-4 | -13: P-609 | H563SP-4B; snubber -15: 563B25-4 |
| Short pintail lockbolts using letter 'Y' | 5 | (sleeve -1) 563B12 / anvil -11 563A14-5 / ejector sleeve -12 563A13-5 | -13: 513-077 | H563SP-5B; snubber -15: 563B25-5 |
| Short pintail lockbolts using letter 'Y' | 6 | (sleeve -1) 563B12 / anvil -11 563A14-6 / ejector sleeve -12 563A13-6 | -13: 563-031 | H563SP-6B; snubber -15: 563B25-6 |
Parts list
| Item | Part number | Description | Qty |
|---|---|---|---|
| 1 | SEE TABLE (563B2 / 563B12) | SLEEVE | 1 |
| 2 | 563B3 | DRAWBOLT | 1 |
| 3 | 562A11 | SPACER | 1 |
| 4 | P-97 | LOCKWASHER | 1 |
| 5 | P-71 | SCREW, SOC HD CAP | 1 |
| 6 | 563A10 | SCREW, BUTTON HEAD | 2 |
| 7 | 563A7 | GUARD | 1 |
| 8 | 563A4 | EXTENSION | 1 |
| 9 | P-240 | SCREW, FLAT HD SOC | 2 |
| 10 | 563A8 | SPRING, RETAINING | 1 |
| 11 | SEE TABLE | ANVIL | 1 |
| 12 | SEE TABLE | SLEEVE, EJECTOR | 1 |
| 13 | SEE TABLE | JAWS | 1 SET |
| 14 | 563A27 | ADJUSTING WASHER | 1 |
| 15 | 563-B25-() | SNUBBER; SEE TABLE | 1 |
Notes from the maker
- Clean anvil (11), drawbolt (2) cavities and jaws every 1,000 installations or on failure; replace as needed. Use washer (14) only if jaws cannot open sufficiently to pass spent pintail. Spacer (3) tight with screw (5) but drawbolt must slide freely. Loctite 242 (removable) on threaded components; lubricate outside of jaw set with Lubriplate.
Where to buy
AmericaDistributor coming soonOur partner for this region is on its way
EuropeDistributor coming soonOur partner for this region is on its way
OceaniaDistributor coming soonOur partner for this region is on its way
Distributors coming soon.
Sources
- Cherry Aerospace, Tool Sheet TS-H563B, Rev. D, 10/12/17 — Lockbolt Offset Pulling Head
Educational reference only. not approved data. Always consult the applicable SRM, AMM, or AC 43.13-1B and your certifying authority.